WM27460W Jenn-Air Microwave Oven Combo - Instructions

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

STEP 1 GO TO YOUR ELECTRICAL PANEL AND SHUT OFF THE BREAKER OR REMOVE THE FUSE. A drill/driver with a phillips bit and extension is all you need. The 1/4" extension is the correct size for the hex screws. Remove them, then the phillips screws and put aside. Remove the control knobs, then the small screws behind them. Remove the trim and clean as it is most likely somewhat greasey, pull the clock board away from the range so that you can disconnect the wires. Lift the tabs holding the ribbon cable to the board and remove the cable. Now that wasn't as hard as you thought it would be was it? Now reverse the proceedure and you will have a working stove again and will have saved a $100 service call. Don't forget to reset the breaker.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Followed provided video

Easy peasy.....Turn off the power in the breaker box to the oven. Take the racks out of the oven,remove the two screws in the very back and pull the element out a few inches(don't be afraid, you may have to use a little force). Pull the clips off of the element and remove it. Replace with the new element and reverse the proceedure. I love knowing I found a websight that had what i needed, was easy to navigate, and offered instructions with the part. NICE!

I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!