Models > WJRR4170G1WW > Instructions

WJRR4170G1WW General Electric Washer - Instructions

All Instructions for the WJRR4170G1WW
106 - 120 of 421
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The washer was shaking a lot
I had to take out the front panel to access the Tub. Afterward the work wasn't hard.
Parts Used:
Tub Dampening Strap
  • Luiz from Bethesda, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
knob would not engage dial behind it
Removed clip (keeper), behind knob, releasing it from shaft. Replace with new knob, and clip.
Parts Used:
Timer Knob
  • jerry from pomeroy, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaked on floor
Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!
Parts Used:
Pump to Tub Inlet Drain Hose
  • Steve from Ogema, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The knob on my washer would not turn so I could select load size
I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.
Parts Used:
Timer Knob
  • Karen from Canastota, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Parts Used:
Tub Dampening Strap
  • Roger from Longmont, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not agitate.
Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.
Parts Used:
Agitator Coupling
  • Foris from Nome, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My washer started leaking water out of the bottom.
I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.
Parts Used:
Pump to Tub Inlet Drain Hose
  • Wallace from Delbarton, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not pump out water
Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.
Parts Used:
Drain Pump and Motor Assembly
  • stephen from brooklyn, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Debris in pump
Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Parts Used:
Drain Pump and Motor Assembly
  • Howard from Davie, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old washer knob
Removed clip from knob and pulled out old knob.Then got new knob and installed with the new clip ,very easy job.
Parts Used:
Timer Knob
  • Pablo from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Control set knob no longer turned the setting dial
I reviewed the service guide on Partselect and was able to take the old knob off the washer and say that the teeth on the knob had worn off, I called in and ordered the part on Saturday and the part was delivered in Wednesday, within 2 minuets from getting home from work the washer was fixed. My wife was ready to go out and buy a new washer when it only cost a little over $13.00 to get it fixed.
Parts Used:
Timer Knob
  • David from Jonesboro, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
Parts Used:
Drain Hose
  • Mohammed from Berkeley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer was making noise.
Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.
Parts Used:
Tub Dampening Strap
  • Matthew from Inwood, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisey,out-of-balance spin cycle
Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.
Parts Used:
Tub Dampening Strap
  • FRANCIS from BRICK, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was not turning on.
I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working
Parts Used:
Control Knob and Clip - White
  • Erica from ATLANTA, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WJRR4170G1WW
106 - 120 of 421
Back to Top