WGG755S0BE00 Whirlpool Range - Instructions

shook bottle and painted waited a day and repeated

This is a double oven unit. Both the upper and lower igniters are easy to get to, with just a few screws to remove. However in order to reach the quick disconnects, the back of the oven needs to be removed. So there are a bunch of screws to take off and the oven needs to be moved away from the wall. Pulling out the igniter wires and putting the new ones back in, is easy. Then put all the screws back on and move the oven back to the wall. Don't forget to disconnect the power when you do all this.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

I had to wait week for parts that were supposedly in stock No notice about delay I had to call to find out you really dropped the ball on this one

Turned off the gas line & unplugged the oven. Pulled oven away from the wall to access the back of the oven. Removed the back panel (screws) on the oven & the few inner oven parts covering the broken igniter. Sprayed WD 40 on the threads of screws holding the old igniter in place. Removed old igniter screws with a nutdriver & unplugged it from the back of the oven. Installed the PartSelect replacement igniter & plugged it into the wiring receptacle. Reassembled the parts covering the new igniter & screwed the back panel back onto the oven. Plugged oven in, turned the gas back on & pushed the oven back into place. Tested the new igniter. Woohoo, oven works again & wife if happy!

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

ordered new broiler pan

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

Just replaced insert pan - was able to identify it on the internet web site by inserting model number. Ordered part on line and got it within a week! Easy peasy!

The lower oven would not heat up, the temperature stayed at 100. I'm pretty sure the same instructions apply for the upper oven. This is a pretty straightforward repair with a couple of minor bear traps. 1) Remove the oven door by simply lifting it up off the hinges. Not absolutely necessary, but helpful to get your head inside the oven. Not a bad idea to vacuum out the oven floor at this stage. 2) Remove the two Philips head screws at the front of the burner pan cover - the screws are at the very bottom inside the oven. 3) The pan cover lifts straight out of the oven, set it to the side. 4) Remove the burner cover held down by either one or two wing nuts - my oven only had one wing nut from the factory - nice job Maytag on your quality control!! 5) Loosen the screw holding down the burner cover in the far back right corner. This cover is a steel rectangular box that is a shield for the burner gas / air connection. Turn the box around to expose the burner end. 6) Remove the two screws that hold down the burner assembly. One screw is at the very front of the oven. The other screw is on the left side of the burner at the rear. Do NOT remove the pan held down by 6 or more screws. On my oven, the left rear screw was stripped. It stripped in a very weird way that took a long time to remove it. The threads inside the metal were fine, but the threads that had been exposed to heat were brittle and fell off. That meant the screw backed out about 3/4 of the way and then kept turning. This is where pliers come in handy. It will take some pulling up and turning with pliers to get those stripped screws out. I didn't want to cut off the screw because the cut out part would fall back into the lower pan. 7) Pull the oven out from the wall and unplug it from the electicity. Remove the 3 screws holding the left rear metal panel in place. There are two screws along the far left side and one down lower on the right. The panel is connected to the one next to it with tabs. 8) Unplug the ignitor. There is a white fireproof wire that comes up from the bottom of the oven that plugs into a white automotive style clip connector. Push the tab to release the clip and unplug the wire. 9) Wrap some stray wire or string around the plug to use as a pull wire when reassembling the oven. 10) Go back to the front of the oven and lift out the burner, be careful not wo pull your pull wire all the way out of the oven. Untie the pull wire. 11) Remove the two philips head screws that hold the ignitor to the burner bracket. 12) Reassemble! Attach the new ignitor with the two screws. 13) Push the wire into the lower part of the oven. 14) Go to the back of the oven and pull the wire through the oven wall. 15) Drop the burner in, making sure it mates up with the gas tube in the back right. 16) Flip the rectangular burner shield back and tighten it down. 16) Replace the two screws that hold down the burner tube, front and rear. 17) Replace the burner shield with the wing nut(s). 18) Replace the burner cover, or floor of the oven. 19) Go to the back of the oven, plug in the ignitor wire. 20) Replace the rear panel cover and secure it with the three screws. JOB FINISHED! Plug in the stove and push it back. The oven takes a few minutes to start heating, you should be able to see orange glow around the slots in the floor of the oven.

Removed six screws on the valve cover using Phillips head screw driver. Three are along the top on the burner side and three are underneath, needing the upper oven door to be opened to gain access. Removed the old valve using screwdriver and 7/16 end wrench. Used same tools to reassemble. Only problem is the valve retaining clamp is hard to get on unless you position it first, before connecting the valve to the line that runs off to the burner. Otherwise, it would have been fairly easy. These valves will stick if liquids are allowed to drip down and under the valve knobs. The channel in the valve stem takes the liquids down to the valve and can cause frozen valves. I bought 3 extra valves to have on hand in case of future failures.