WGG755S0BE00 Whirlpool Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed old ingniter with screwdriver. Installed new igniter, but had to remove connector in order to electrically connect using twist on connectors.

1. Pulled range out from its cabinet setting and turned off the gas and unplugged the electric cord. 2. Removed all knobs (and soft pads) to burners. 3. Removed curved cover that covers the burners gas valves, gas manifold and igniter harness. 4. Removed a part that could be referred to as a flange or riser that is attached to the top of the range front at the burner level which the top of the curved piece is attached to. 5.The igniter attachments to the gas valves come off by pulling them away from the valve. I pulled away the one for the grill. 6. With these parts removed, eye sight and 1/2" open end wrench access is given to where the gas valve is attached to the burner gas line. 7. Disconnected the valve from the burner line. 8.Removed the bracket that holds the valve in place, thus removing the valve. 9. Installed new valve and bracket and attached valve to burner line. 10. Reattached the igniter part to the valve, then attached the flange (#4), then the curved cover, then the burner knobs (and soft pads). 11.Reconnected the electric cord and opened the gas valve. 12 Pushed the range back into its cabinet place and pushed the 'Cancel:' mark as directed by the digital read-out on the range's back riser control panel. Checked for gas leak. None. It took a bit of scrutiny to see what to remove and in what sequence.

You Tube!!! Didn’t find my exact oven, but watching a couple of videos was extremely helpful. Replacing the igniter was basically simple, but since it was a first for me, I took my time. Probably saved $200. The part was just over $100.

Took the old levelling leg out and screw the new one in.

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Replaced Igniter, only problem was the connector was in the back of the unit. I had to take off the back of the unit. About 12 small hex screws to make connection. Other than that it was pretty easy.

Easy instal most of time was taking off and replacing back panel Found watching how to videos helpful

Shut gas off. Took cover off of valve assembly. Removed broken valve and installed new part. Turned gas on and checked for leaks. Installed cover on valve assembly.

I repair it by shutting off the gas. removing the back panel of the stove . unplug the electrical sensor cord to the igniter. Then replace with new one.

Just removed the shield (2 wing nuts) than the burner (1 Screw). THe back needs to be removed to unplug the igniter. I than reversed the process until I got to the plug and found that I had 2 male ends. I than had to remove everything and go back to square one until I find the part with the correct end (which should be Female) I'd check this before getting too deep into the repair.

Unplug range

Shut off gas supply

Remove rear panel screws and panel with nut driver

Disconnect power plug from broiler element igniter

Open upper oven door

Remove screw from the front of the gas burner.

Remove screw using nut driver from rear of gas burner

Remove gas burner from oven and pull cord through from rear panel

Using nut driver, remove igniter from mount on gas burner

Install new igniter on mount on gas burner using nut driver

Reinstall is reverse of disassembly

Connect power and turn gas back on. Test igniter by activating broil on upper oven

Removed old racks, installed new racks. Recycled old racks.

This is the second time had to change burner on this range. Last time was the left front. Since I had done it before knew better about being careful of the wiring. Last time sliced it and had to repair it. Also last time had to have a neighbor unscrew old knob. This time had no problem unscrewing the knob. I did have to adjust the know to be align properly. Also forgot to slip to bottom clamp over the first time and again had to reassemble. Once I got it assembled correctly no problems, works great. I had ordered the wiring harness that I had sliced but it was still intact so saved it for another time.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.