WGD9371YL1 Whirlpool Dryer - Instructions

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from over time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

Watched the tutorial online. Took the back off- replaced the fuse. Put the back on . It was extremely easy !!

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Replace the switch in diagram #4.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.

Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.

I watched the online video first, which made the removal and installation fast and easy.

went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.