Models > WFG114SVQ0 > Instructions

WFG114SVQ0 Whirlpool Range - Instructions

All installation instructions for WFG114SVQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WFG114SVQ0
1-15 of 44
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

our oven would not heat up

  • Customer: sharnette from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 32 of 35 people found this instruction helpful
My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have .

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 49 of 101 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.

Oven would not heat.

  • Customer: Nedra from Alsip IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 13 of 15 people found this instruction helpful
Installing the part was really easy. I first turned the gas off, simply remove two screws tht hold the igniter in place. I then remove four screws from the back panel and disconnected the part. The feedback from other users on your site made me realize how easy it was. It took less than thirty minutes.

The igniter would turn orange but wouldn't fire up, so the oven wouldn't heat up.

  • Customer: Lisa from Livermore CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
I just unscrewed the old one out, which was 2 screws and screwed this one in. But the thing that was best of all was how fast the part came in. It literally came the next day.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Oven stuck in cleaning mode

  • Customer: Hal from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 23 of 52 people found this instruction helpful
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.

Oven would not heat

  • Customer: sean from san bernardino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 8 of 10 people found this instruction helpful
Amazing after two years off frustration due to unsurety of problem went to your site found part problem in question that matched my problem.two screws and a plug now im burning like im supposed to.success

Igniter glowed but oven would not light

  • Customer: Kenneth from Garden Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
We looked up the trouble shooting page on PartsSelect and ordered the part recommended. Part arrived very quickly. Simple installation, two screws and plug in. Problem fixed.

No heat in the Broiler/oven.

  • Customer: Matthew from Reno NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 7 of 10 people found this instruction helpful
Removed the panels, disconnected and dismounted the igniter and installed the new one. Pretty simple.

Ignitor would glow but not power gas valve

  • Customer: Jacquelyn from Billerica MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 10 people found this instruction helpful
New ignitor fixed the problem

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

No Power from Touch Pad

  • Customer: Beth from Osseo MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Burners still worked but nothing in the oven because the touch pad had no power due to an electrical storm. I removed 6 screws from the back and then two screws from the circuit board and 3 connectors. Removed the old circuit board and put the new one in. Reconnected the 3 connectors and checked to see if that fixed the issue. Hardest part was getting the back plate back on. I would do this again - replacement part was around $100 and a new range over $300.

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 12 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
All Instructions for the WFG114SVQ0
1-15 of 44