Models > WFG114SVQ0 > Instructions

WFG114SVQ0 Whirlpool Range - Instructions

All installation instructions for WFG114SVQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WFG114SVQ0
31-43 of 43
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

  • Customer: Joanne from Negaunee MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Pilot tubing developed leak at clamp location

  • Customer: William from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I disconnected gas line and removed screws holding the 4 pilot assembles, lifted the top of stove and removed and replaced the tubing. Pretty straight forward installation..

Gas oven would not heat up

  • Customer: Elizabeth from Woodstock GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

Oven would not light

  • Customer: Marva from McDonough GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

oven temperature did not stay as set

  • Customer: Paul from Cornelius NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Pilot light wasn't working.

  • Customer: wilma from Ashdown AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

oven will not heat up

  • Customer: Marie from Schaumburg IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

hinge was rusted and broken, the oven door wasn't able to open or close.

  • Customer: Karl from Miami FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
it was abit difficult to remove the rusted hinge because of rust, but after getting it out and securing the new one, I realize I had an even bigger problem. The new hinge was closed and the spring was very tight.After a closer look at the other side of the oven door where the hinge was intact, I saw a hole in the hinge when it was opened. So I opened the new hinge by pulling it open and exposing the hole, put a pin in the hole.I then put the hinge in position and put in the screws.But now the door wouldn't go into position. I then had to put pins on both hinges and slide them in at the same time,locking them into place.This was the first time i ever took out an oven door or attempted any stove repair.

Stove kept turning off

  • Customer: Richard from Wooster OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Oven would not light

  • Customer: Gary from Springfield OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

THE OVEN DID NOT COME ON.

  • Customer: lore from lampasas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
IT ONLY TOOK MY HUSBEND 6MIN TO PUT IN THE NEW OVEN IGNITER. BUT IT DID NOT WORK, SO I CALL YOUR CENTER AND THE REP THERE TALK MY HUSBEND AND TOLD HIM HOW TO UNLUCK THE KEY BORD, AND THAT WORKED. THANK YOU FOR ALL THE HELP.

Oven shutting off after temp reached 350

  • Customer: Ken from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.
All Instructions for the WFG114SVQ0
31-43 of 43