WCSR2090DGWW General Electric Washer - Instructions

My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.

Removed the screws for the control panel and replaced the load switch and valve body in about 20 minutes. Simple fix and it's working perfectly!

replaced Tub dampeners Straps.

Removed bottom washer plate. Placed belt on small, grooved pulley. Started belt on larger pulley. Clamped lock pliers to larger pulley to prevent belt from slipping off. Turned belt onto larger pulley by turning and pressing the belt close to the smaller pulley. Adjusted belt and replaced bottom plate.

Replaced lid switch with wire harness. Video available on this web page. The technician said bad motor. We counted the flashes, light on top of motor, was 7 times. Diagnoses are very important, save you money! Do it more times, be sure. Biggest problem is socket size for the screws, size 6,5mm or 1/4 inch. Do not call technician or throw away your washer!...

First I removed the old part (2 screws)
Pulled off 4 wires (maybe the wrong word, I'm not a professional!
Put the new part in-turned the water on and had a stream of HOT water-yay
I had been putting this off because no one in my family had noticed (except me) and with my husband out of work it seemed like a low priority, but when my daughters came home for Christmas, they said "There's no hot water in the washing machine" so I took the plunge--I cannot believe I waited that long!
It literally took me seven minutes!

When disassembling I could not remove the 1 3/4" tub nut with in house tools and had to order the spanner wrench. Almost mandatory unless you have a socket wrench.

Removed front panel, cut two wires to switch ( color coded ) snapped old switch out and installed new switch, connected wires with wire nuts. Removed two screws in lid, removed magnet and installed the new one. A caveman could do it!

I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy

I replaced the old knob with a new one.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.