Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WCSR2090DGWW

WCSR2090DGWW General Electric Washer - Overview

Get Parts and Repair Help for WCSR2090DGWW

If you know the washer repair part you need, you can browse the list of all parts on the WCSR2090DGWW, or you can search by name or part description. You can also find your part by where it is located on the WCSR2090DGWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WCSR2090DGWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.38

Tub Dampening Strap

The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noi...

$12.88

Drain Hose - 4 1/2' Long

The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access the hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.

$3.50

Timer Knob Clip

The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip....

$7.52

Tub Seal

The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an actual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault. NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.

$8.01

Knob and Clip

$12.78

6-Rib Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$57.04

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will...

$3.29

Tub Bearing

This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a wash cycle. The most common reasons for needing to change your tub bearing is if your appliance is noisy or shaking/moving during the wash cycle, another common symptom is leaking water. This part is sold individually and measures to have an inner diameter of roughly 1 inch, and an outer diameter of roughly 2 inches.

$4.48

Split Ring

This split ring is two inches in diameter.

$3.90

Drain Hose Clip

This drain hose support clip is a piece for your washer. The purpose of the drain hose support clip is to hold the drain hose in place by attaching to a cabinet. This piece is off-white and is roughly 3.5 inches long, almost 2.5 inches wide, and less than half an inch thick. To install this piece onto your washing machine you will need a quarter-inch nut driver. Before starting this repair, make sure to disconnect the power source to your washer, as well as the inlet fill hoses.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 277 of 293 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

washing machine would not go through all cycles or agitate

  • Customer: Brian from Millerplace, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 205 of 255 people found this instruction helpful
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok. read more

washer was overfilling

  • Customer: Matthew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 174 of 197 people found this instruction helpful
Removed the water level pressure switch and the water inlet valve to test parts for proper operation with an ohm meter. Electrically, the switches seemed to work fine so I thought it was probably a mechanical water valve problem. I ordered and replaced both parts anyway just to be sure and potentially save time. read more