All Installation Instructions for General Electric Washer WCSR2090DGWW

noise when in wash cycle

Inside the appliance is an instruction sheet that describes replacing the part and followed it mostly. To improve your instructions, pictures with the instructions are much more effective and easier to understand.

Parts Used:

Shaft and Mode Shifter Assembly

James E from Sandy, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

Was this instruction helpful to you?

Thank you for voting!

cold water would not stop running

Took out the old part and easily replaced it with the new part.

Parts Used:

Dual Water Inlet Valve

Kelvin from Richland Hills, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Thank you for voting!

Washer was overflowing both wash/rinse cycles

Ok it was easier than typing this email. Remove selector knob. Use star*screwdriver to remove 4 screws at top. Pull the panel out toward you, lay down.Pry the lock tab up slightly with knife/flathead to clear the groove twist switch half turn counterclockwise and remove. Pull the vacuum hose off. Remove 2 wires. Now do it again in exact same order only in reverse. Youre done. Saved aprox. $280.00 and was a hero for the rest of the day.

Parts Used:

Water Level Pressure Switch

Dennis from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Timer knob broke

1. Consulted a knob swami. 2. Obtained an advanced degree in business. 3. Consulted a civil engineer. 4. Undid knob clip 5 removed broken dial. 5. replaced new dial 6. replaced clip 7. washed clothes. Steps 1-3 unnecessary. Step 7 - Optional

Parts Used:

Knob Dial

Gary from HARRISBURG, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Washer wouldn't agitate

I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!

Parts Used:

Agitator Coupling

Jeri from Jourdanton, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

water would sometimes overflow on floor

Replaced dual inlet valve. Problem solved

Parts Used:

Dual Water Inlet Valve

Waldemar from Poway, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

timer knob did not advance

watched supplied on-line video

Parts Used:

Timer Knob

stephen from pittsburgh, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Cold water was dripper after each washing cycle.

1)Remove the 5 screws from the back panel to gain access to the dual inlet valve. 2)Disconnect the wire from the valve. Then, remove the screws the hold the valve. Then, remove the C-clamp from the valve to get it loose. 3) Then, reverse the procedures to install the new valve.

Parts Used:

Dual Water Inlet Valve

Roque from Brentwood, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

No hot water fill

Installation went okay but still only get cold water fill

Parts Used:

Temperature Switch - 3 Position

Joanne from Millican, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

No cold water coming in

Viewed the hot/cold valve. I saw that the cold water solinoid was burned. Ordered new valve and replace old valve. On my washer 4 screws held the switch panel, easy to remove and gave me plenty of room to veiw and do the repair.

Parts Used:

Dual Water Inlet Valve

Maurice from Port St.Lucie, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The timer knob was broke

Watched the video you had on how to replace it and did it like you showed and said and it worked fine.

Parts Used:

Timer Knob

Thurman from Marshall, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

knob stripped

needle nose pliers to pull out old tab behind old knob. simply pop new knob on when you remove old. video gave me self confidence to do it myself.

Parts Used:

Timer Knob

sandra from north windham, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Overflow when filling

My washer was overflowing when filling. Stopped filling when i unplugged from wall so i knew it was the pressure switch because the tube was fine. It took 28 hours from the time i placed the order to the time it hit my front porch. Got home from work and two minutes later i was washing clothes. Thanks for all the info, Tom

Parts Used:

Water Level Pressure Switch

Thomas from Clyde, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Could not advance the timer to start the cycle

Use a flat head screw drive to push the clip off the timer stem which holds the knob, which is behind the knob, pulled old knob off, place new knob on timer stem, used needle nose pliers to push new clip on timer stem to hold knob on

Parts Used:

Timer Knob