W246-C Jenn-Air Wall Oven - Instructions

Easy as pie to do this repair. You first remove the 2 screws holding the element in. Then you carefully pull out the element and remove the wire clips at the ends. Just reverse the process with the new part.

By the way, I ordered my part from parts select on a Friday afternoon and it was on my doorstep Saturday morning..... and this was with regular delivery!
I would buy again in a heartbeat from parts select.
Joe Golub

As the probe is a plug-in item that would normally be out of the oven, there was nothing more to the repair than checking that the new probe plug fitted the socket and that it was detected by the oven. Then the old probe was consigned to the trash.

Everything checked out, and the probe was used satisfactorily within a couple of days.

First I verified that the breaker was OFF!

We have a build-in Jenn-Air oven. After finding the four screws that held the oven into the enclosure, sliding the oven out was pretty easy since my wife helped me. We used a nut drive to remove the 18+ screws holding the top on the oven.

Using the Internet we entered the switch part number. The number on the switch did NOT help finding the switch. We used the model number and with the exploded drawing on the PartSelect.com web site it was fairly easy to identify the switch.

I ordered the switch and specified two day delivery. This was on a Saturday. The switch arrived on Tuesday.

We had to remove the front glass plate to get to the screws holding the switch. I drew a diagram of the switch with the wire colors/numbers. I left the wires on the old switch. I removed the old switch with the wires still attached then installed the new switch. I moved the wires one by one. Then I verified the correct connections based on my drawing.

We re-installed the 18+ screws and slid the oven back into place. Turn on the breaker and baked a pie.

The job is pretty easy,4 screws pull ot coil,pull out of back of oven to remove the connections,the only problem that I had was the connecters on the new coil was not the right angle,fixed this by bending the connecters very carefully than a piece of cake.

I didn't. Don't know how to get to light bulb to change it for this specific model

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the bad element - two screws, and tested it on my meter as recommended. The test meter showed it was bad, so I ordered a replacement element from PartSelect. I did check getting a part from a local dealer, and it would have been $10 more. The help and recommendations I recieved on the PartSelect repair forum make it easy.

Terry Hausler

My wife removed old element and replaced new element by removing and rescrewing 2 screws and detaching and retaching 2 wires to thr respective elements in about 5-10 minutes.

The heating element is held in place by two phillips screws which were rusted fairly tight, visible at the back of the oven. I tapped my screwdriver with a hammer as I loosened them. (I would have used liquid wrench if the hammer did not work) Two wires are fastened to the element by two clips that you can slide off by hand. Slip the wires off the old element and onto the new element and install the two screws and you are done.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

This was obviously not a hard repair, I just replaced the knob. I would like to say that I did receive the part in just a little over 24 hours. That was nice!

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

I removed one screw easily. The other screw was difficult to remove without stripping it. I sprayed wd 40 and let it sit overnight. The next day, my husband sprayed it again and after trying several different size phillips screwdrivers, he got the second screw out. He easily removed the element and then the two wires from it. He attached the two wires and replaced the screws. We tested it and it worked. The best part is: my husband scrubbed the oven before putting all the parts back!

I opened the oven door and unscrewed the two screws that connected the element to the back of the oven. I then pulled the element forward but it would not expose the electrical connections that powered it. I pulled a little harder and it would not pull through the insulation. I then decided that it must be accessable from the back. I took off the door the lighten the oven. I pulled the oven out of the cabinet till the conduit was taught and I could just barely see that there wasn't a panel to access the connection. I then put the back into the cabinet and pulled a little harder yet on the element and the connecters pull through the insulation. I was then able to test the element with the multimeter and decide the power was getting to the element but no heat. I ordered the part the next day. Recieved it the day after that, smokin' fast service I must add. Installed the element and it works like a new one. My wife loved it and then she loved me.