W206B Jenn-Air Wall Oven - Instructions

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the bad element - two screws, and tested it on my meter as recommended. The test meter showed it was bad, so I ordered a replacement element from PartSelect. I did check getting a part from a local dealer, and it would have been $10 more. The help and recommendations I recieved on the PartSelect repair forum make it easy.

Terry Hausler

My wife removed old element and replaced new element by removing and rescrewing 2 screws and detaching and retaching 2 wires to thr respective elements in about 5-10 minutes.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

The heating element is held in place by two phillips screws which were rusted fairly tight, visible at the back of the oven. I tapped my screwdriver with a hammer as I loosened them. (I would have used liquid wrench if the hammer did not work) Two wires are fastened to the element by two clips that you can slide off by hand. Slip the wires off the old element and onto the new element and install the two screws and you are done.

Much to my horror, what was described as a simple, 15-minute replacement, took 3 days! In order to replace the oven door gasket, I had to disassemble the entire door. Every photo I saw of the gasket showed it as a flexible part: gently pull out the old one and push in the new. What I received in my order had a frame. In order to replace it, I needed to unscrew the door parts. Unfortunately, I made a few rookie errors, primarily because I kept thinking the next screw would release the gasket frame. So I neglected to keep track of the screws I removed, and I didn’t take any photos!
I must have used half a roll of masking tape to keep parts together; I did not have 5 hands! When I released everything and nestled in the frame, I had even more trouble replacing all the screws I took out. The majority of holes did not line up. So I just did the best I could, put in as many screws as I could. But after three days of working, I finally finished. It all held together, and the door did what it was designed to do. Really a repair horror. And I am not an incompetent novice!

I opened the oven door and unscrewed the two screws that connected the element to the back of the oven. I then pulled the element forward but it would not expose the electrical connections that powered it. I pulled a little harder and it would not pull through the insulation. I then decided that it must be accessable from the back. I took off the door the lighten the oven. I pulled the oven out of the cabinet till the conduit was taught and I could just barely see that there wasn't a panel to access the connection. I then put the back into the cabinet and pulled a little harder yet on the element and the connecters pull through the insulation. I was then able to test the element with the multimeter and decide the power was getting to the element but no heat. I ordered the part the next day. Recieved it the day after that, smokin' fast service I must add. Installed the element and it works like a new one. My wife loved it and then she loved me.

I removed one screw easily. The other screw was difficult to remove without stripping it. I sprayed wd 40 and let it sit overnight. The next day, my husband sprayed it again and after trying several different size phillips screwdrivers, he got the second screw out. He easily removed the element and then the two wires from it. He attached the two wires and replaced the screws. We tested it and it worked. The best part is: my husband scrubbed the oven before putting all the parts back!

I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.

Removed old element, 2 screws, cleaned oven , 60 minutes, replaced with new element, working like new, wife thoroughly impressed...