VWSR4150DAWW Hotpoint Washer - Instructions

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

removed top and replaced .

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

New dual water inlet valve.

Changed the dual water inlet valve.

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

used pliers to pull broken portion of knob off timer shaft then pushed new timer knob with clip onto shaft.

Ordered the parts on Sunday, received them on Tuesday.

Removed the remaining broken piece. Pushed on the knew knob!

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

Was easy to remove the broken parts because they were loose already due to the broken finger in the agitator. It was good that I ordered the coupling kit because the bolt showed corrosion already. With the new parts I was able to see how they all clipped on together so I set myself to unbolted the coupling, install the new coupling, tighten it, alined the agitator to it, pushed into place and,... vuahla!!! fitted and worked like a charm.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

removed the old agitator, removed one bolt from coupling.replace coupling, put new bolt on and sled new agitator on. just that sample, works great!! thank you