VWSR3110W0WW Hotpoint Washer - Instructions

I removed the agitator by simply pulling up. I then removed one bolt to get the agitator coupler off. I installed the new coupler, replaced the bolt and slid the agitator back down.

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

Opened lid and place on agitator ... finished

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

replaced them & working fine now....

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

replaced clutch assembly. unplug power; turn off water, disconnect hoses from faucet; remove drain hose from drain; shop vac water from basin through drain hose. bungee hoses and cords, relocate to garage, place blocks, lay unit on blocks on back, remove front cover, mark electrical connections, disconnect- move aside, support motor, i used a ratchet strap behind motor around the tub supports, removed nuts from motor mount bolts, release strap, tilt and remove motor, place on plywood, use opposing small pry bars to remove clutch assembly; remove rust from motor shaft, install new clutch, re-install motor, install belt, tighten ratchet strap, to tighen belt, re install mount bolt nuts, reconnect electrical connections, remove strap, clean gunk from washer case floor, double check connections, mount bolts, belt tightness, re-install front cover, re-position washer, reconnect hoses, and power cord, turn on water, open fron cover, check for leaks; run rinse spin cycle to test - confirm no leaks, ops check complete, good to go. total time, including removing repositioon and removing water, about an hour, clutch replacement time about 15 min's.

Turned off the water and disconnected the water lines. Took of the control panal, only 4 screws and got access to the dual inlet water valve. Device removes with 2 screws and power connectors slide off. Reverse removal and your in business. So easy to do, part was an exact fit. Don't buy a new washer, fix your old one!

Very easy just pull straight up on agitator and remove bolt on coupler. Install new coupler and line up agitator and push down. Done

Pulled agitator off existing agitator coupling. Removed and replaced agitator coupling. Snapped agitator on. One of the easiest appliance repairs I have ever attempted.

Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!