VBSR2080W0AA Hotpoint Washer - Instructions

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

replaced them & working fine now....

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

replaced clutch assembly. unplug power; turn off water, disconnect hoses from faucet; remove drain hose from drain; shop vac water from basin through drain hose. bungee hoses and cords, relocate to garage, place blocks, lay unit on blocks on back, remove front cover, mark electrical connections, disconnect- move aside, support motor, i used a ratchet strap behind motor around the tub supports, removed nuts from motor mount bolts, release strap, tilt and remove motor, place on plywood, use opposing small pry bars to remove clutch assembly; remove rust from motor shaft, install new clutch, re-install motor, install belt, tighten ratchet strap, to tighen belt, re install mount bolt nuts, reconnect electrical connections, remove strap, clean gunk from washer case floor, double check connections, mount bolts, belt tightness, re-install front cover, re-position washer, reconnect hoses, and power cord, turn on water, open fron cover, check for leaks; run rinse spin cycle to test - confirm no leaks, ops check complete, good to go. total time, including removing repositioon and removing water, about an hour, clutch replacement time about 15 min's.

Turned off the water and disconnected the water lines. Took of the control panal, only 4 screws and got access to the dual inlet water valve. Device removes with 2 screws and power connectors slide off. Reverse removal and your in business. So easy to do, part was an exact fit. Don't buy a new washer, fix your old one!

Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

1) Researched internet for parts to make repair
2) Tested the cold side to make sure the only problem was the valve.
3) Ordered part from PartSelect
4) Made repairs after going to hardware store to purchase a set of torx bits to loosen the front panel so I can replace the dual valve assembly.

Only tools needed #1 Phillips and #15 Torx

remove top control panel & r&r water level/pressure switch.