Models > TWX233RBW3 > Instructions

TWX233RBW3 Tappan Washer - Instructions

All installation instructions for TWX233RBW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TWX233RBW3
61-75 of 130
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer leaking

  • Customer: Kim from Ridge MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.

the drain hose was leaking

  • Customer: STEVEN from HAMPTON GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

The pump axle seal was leaking

  • Customer: Scott from Fremont CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 1 of 2 people found this instruction helpful
This is the third time it has been replaced. They last about 2-3 years. Made sure pump was full of water before starting etc so we didn't start with a "dry" pump.

The actual repair and parts ordering went just fine.

Scotty

Bottom "Screw", which is the front leg of the washer was broken.

  • Customer: Linda Lahann from Freehold NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

water leaked into machine when turned off

  • Customer: Henry from Frenchtown NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....

it dont drain

  • Customer: charlotte from jersey city NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
part was fast easy to put on know work better then before

hot water kept filling the tank

  • Customer: Bob from Birdsboro PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

Washer Not Draining

  • Customer: Craig from Asheville NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.

old pump leaked

  • Customer: Robert from Glen Allen VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 1 of 3 people found this instruction helpful
Replacing the pump assembly only involved:
1. Unplugging the washing machine!
2. Removing 2 screws to take off the washing machine's lower front panel.
3. Removing 2 bolts to take off the cover over the remote pump assembly.
4. Changing out the pumps required:
A. Unscrewing the 2 screws that secure the assembly harness to the washing machine's base.
B. Unclasping the 2 tubes using curved jaw pliers.
C. Disconnecting the electrical connectors by hand.
D. Removing 2 bolts from the assembly harness and the pump assembly.
5. Reverse steps 1 - 4 to install the new pump.

Discharge hose was leaking

  • Customer: John from Hyattsville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
This is a newer washer, but I don't know the age. I just bought the house...!

I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.

Inlet valve leaked water from supply line(s) back into washer.

  • Customer: John from Powhatan VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Pulled washer electrical plug from receptacle.
Unscrewed hot and cold water inlet hose connectors.
Removed screws retaining backplate.
Removed back plate.
Removed two screws connecting valve assembly to frame.
Pulled two spade electrical wire connectors from valve assembly.
Opened hose clip securing hose on outlet side of valve assembly, using pliers.
Pulled hose from valve assembly.
Valve assembly now free.
Reversed above with replacement valve assembly.

No cold water supply

  • Customer: Harold from Kansas City MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.












































































Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.

Hot water was not entering the machine, but cold water flowed smoothly

  • Customer: Ronald from Saint Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

Cold water was filling slower than the hot water.

  • Customer: Steve from Fort Mohave AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pulled hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.

Pump was leaking

  • Customer: Jose from Staten Island NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Remove old pump, only a scrwedriver needed.
Save myself @ $100
All Instructions for the TWX233RBW3
61-75 of 130