Models > TU800SPPB2 > Instructions

TU800SPPB2 Whirlpool Trash Compactor - Instructions

All installation instructions for TU800SPPB2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TU800SPPB2
31-45 of 75
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The compactor rubber guard was torn.

  • Customer: Judith V from Studio City CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Compactor would not open. Ram was down

  • Customer: James from Flagstaff AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

Plastic Drive gear broke

  • Customer: Terry from Spring TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

Handle broke off. Three screws to replace

  • Customer: Kim from Humble TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Saved screws from old handle, used to mount new handle.

Wouldn't come back up after compacting

  • Customer: mark from st george UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
replaced switch and fixed the problem. Still had one more problem after that though, but got that figured out and fixed that to.

PLASTIC GEAR WHEEL BROKE

  • Customer: Reagan from Glenshaw PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 1 of 3 people found this instruction helpful
Emptied all garbage!
Laid machine on its side.
Removed cover.
Removed left over gear parts by removing pin.
Loosened chain by removing two top left corner screws.
Place new PLASTIC gear in position with chain.
Returned screws to top left corners.
Returned pin to gears.
Make sure chain is taught.
Replace cover.
Lift back up from its side.
Test.

Compactor ram was stuck in the down position and door would not open

  • Customer: Michael from South Boston MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Toe guard was broken, foot pedal was discolored.

  • Customer: Michael from Ashfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 4 people found this instruction helpful
Replaced both, results like new.

Ram quit moving

  • Customer: Hal from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed bottom and replaced gears

Broken Drive Gear

  • Customer: Michael from Painted Post NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Broken handle

  • Customer: Walter from Sudbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Inserted three screws in pre-drilled holes.

unit was missing parts

  • Customer: Richard from glendale AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Installed new parts. Worked fine.

Bought a washer without front leveling feet

  • Customer: Rick from Lennon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Handle fell off

  • Customer: Barbara from Lutz FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 5 people found this instruction helpful
Removed two screws, replaced handle, replaced the two screws. This was so simple! I can't believe we put up with the inconvenience for so long before fixing it!
All Instructions for the TU800SPPB2
31-45 of 75