Models > TGF362BBBA > Instructions

TGF362BBBA Tappan Range - Instructions

All installation instructions for TGF362BBBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF362BBBA
256-270 of 298
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven Did Not Heat

  • Customer: Sandra from Los Angeles CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The oven began to have low heat and then no heat. Read about it on-line and figured it was the igniter for the oven. Found the model number on stove/oven frame behind the bottom draw. Then I looked at a few on-line videos about how to install the piece. I have a convection oven and had to take the fan cover off to remove the bottom inside cover of the stove and I couldn't figure out how to remove the oven door to make it easier...so I had to leave the oven door on the stove. The stove door is heavy so be aware of that issue. Also I needed help...it was a two people operation. I needed to lay the stove on it's back to get to the piece. I needed to cut the wires and remember where everything went it was as simple as the video made it out to be...there were a few more wire connections. There is the issue of the door ...be careful you can stand the stove up and bring it down again but if not be careful/mindful of the door and it's weight and desire to slam closed...maybe a third person would be good to have around. ;) Anyway it can be done. Have patience. Take your time. Have a buddy to help you. Best part...the oven is now heating!! ;) Lovely!

Front and rear glides broke on bottom drawer.

  • Customer: charles from orlando FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the videos on removing and replacing the front and rear glides on the bottom drawer, I was able to take the bottom drawer out, use a screwdriver to pry all the glides out of their slots and snap them all back in place in less than a minute. Without the videos I was completely helpless in knowing the sequences to performing this task.

upper oven would light up but took awhile

  • Customer: robert from des plaines IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
disconnect electrical power to oven , removed face plate to where the igniter connections were. lift cover that is over the igniter in oven, remove igniter from burner, attach ner igniter to burner and route wires inside cavity where connections are. cut connector from old igniter leaving enough wire to splice to new igniter, strip wire and connect using wire nuts, put everything back together and test

oven took very long time to ignite.

  • Customer: Ronald from Keymar MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first we went online to see if others had experienced the same problem, and what they did to fix it. ordered part to arrive within three days. husband removed connecters from old igniter and spliced them onto new one. We felt it should have come with connecters. set burner with new igniter in place, and it worked...Yay! just in time for Thanksgiving turkey!

Igniter glowed but slow or no oven lighting

  • Customer: JAMES from Harrison MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter.

drawer glides broken and missing

  • Customer: David from Coloradosprings, CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy.it took only minutes to install.The how to video was a big help.thank you parts select!

Bottom Panel of over rusted out.

  • Customer: Michael from Manasquan NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

oven wouldn't light

  • Customer: Donna from Trinidad CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
using socket set removed old ignitor,replace with new one and secured using the socket set. The oven lite right up.Service was A1. I ordered on Friday evening and the part was delivered on Monday. Thank you.

no rear drawer glides were in place

  • Customer: Barbara from Satellite Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Inserted the new rear drawer glides

the pullout drawer below oven did not work

  • Customer: Dawn from Palmer AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the rear glides were missing on the back of the drawer so the drawer would pull out but when pulled back in, would tip down and not catch on anything. I ordered the parts then found an instructional youtube and watched it. Easy repair, cheap!

Bottom drawer front guide broke

  • Customer: charles from eubank KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Took a set of pliers and popped the old ones out and snapped the new ones in

Oven would not light

  • Customer: Edward from Pent Water MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Put a new ignighter in the oven I also would like to commend PartSelect for the fast service on the part i ordered it one day and recieved the part the nexted day i would recommend you any time

broken rear door glide

  • Customer: Amy from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Emptied the drawer of storage items. Removed the drawer and attached the new rear drawer glide. Replaced the door in the range and refilled the drawer.

one rear and one front glide missing

  • Customer: Rod from Spencer IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just moved into this house and inherited the oven so I don't know how old it is but I had to put something down in order to submit this review. Popping the glides in place took seconds. I am amazed that I found the parts so easily online and that they arrived so quickly. Usually the simplest of things turns into a time consuming project for me. Thank you!

Oven lights intermittently, smell of gas

  • Customer: Robert from Lakewood NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Model# GLGF366ASD range
Turned off breaker
Removed oven door (see gas range manual for procedure)
Removed storage drawer on bottom of range.
Removed oven racks.
Removed oven bottom panel (2 screws in back of panel)
Removed oven shield (screw on left and right front of panel & nut in middle of panel)
At this point igniter was exposed
Removed igniter by removing the 2 self tapping screws securing igniter.
Note: threads on both screws stripped during removal, requiring both
screws to be cut off for removal.The stripping of threads of these screws
is probably normal due to the heating and cooling of the oven during
operation, making the threads on the screws brittle.
Marked the top wire on the igniter with a black sharpie
Cut both wires as close to the old igniter as possible.
Cut wires on new igniter about 10" long.
Connected new igniter with wire nuts (provided) making sure to connect wire from top of igniter to wire marked with sharpie.
Installed new igniter using 2 new #8x1/2" self tapping screws.
Pulled excess wire & wire nut connections down into the back of the storage drawer area making sure wires were resting on flanged area of panel.
Reinstalled oven shield, panel, racks, storage drawer, and oven door.
Turned breaker back on.
Oven works great.
Note: self tapping screws should be provided
All Instructions for the TGF362BBBA
256-270 of 298