Models > TGF362BBBA > Instructions

TGF362BBBA Tappan Range - Instructions

All installation instructions for TGF362BBBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF362BBBA
271-285 of 303
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Igniter not drawing enough volts to open safety valve.

  • Customer: Christopher from Oakmont PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the oven drip pan and removed the old igniter and cut wires and used the supplied wire nuts and replaced the old part turned the oven on and it ignited.

rear drawer glide broken

  • Customer: william from hagerstown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
rec'd rear drawer glide 2 days after ordering opened package removed from wrappers snapped in place put drawer back in
took nearly 2 minutes to complete 1 1/2 of which was opening packages if you add ten minutes to find and order still under 15 minutes total have used this company before and will use any time something like this is needed. rebuilt my 18 year old dryer motor belts lint filter saved money and got a "new" but old quality maytag same with washer easy to order. quality help if or when needed speedy delivery keep them in business please

Burner would not light because of cracked ceramic collar

  • Customer: Anthony from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The electrode was sparking to ground through the cracked ceramic rather than within the ignition zone. I used spray electronic contact cleaner to free rusted screws (different metals often contract at different rates and separate under the very cold spray). Replacing the electrode was a simple substitution. Also sprayed the spade terminal pair to remove any corrosion. Worked first time.

not heating as setting reads

  • Customer: Debra from Miramar Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched u tube sent by your company, opened back of oven,removed sensor,checked w/ohm meter,ordered part, replaced sensor,replaced back on oven, DONE! works like new amazing help I was given by your staff! I was quoted over $200.00 to come to my house,ck.,fix, and part replaced. My cost was $50.00 + shipping of $7.00. Thank you guys!

Two of theTop gas burners would not spark

  • Customer: Robert R from Lewistown PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

Just had to replace the racks in the stove.

  • Customer: charles from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Gas oven light off time long, strong gas smell in house from long light off time. Oven would not control desired temperature.

  • Customer: Richard from Rockford IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected electric power. Removed oven floor and flame spreader to access igniter. Spliced replacement igniter to original igniter connector plug wires. Mounted new igniter and reinstalled flame spreader and oven floor. Reconnected electric power and checked oven operation. Oven light off time was within 1 minute and oven temperature controlled to all settings up to 450 degres.

Sliced Outlet Cord

  • Customer: William from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.

Oven took a long time to light, did not stay lit

  • Customer: Carol from Campus IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very Easy. Part arrived in less than 48 hours of ordering. Followed the directions included with part and referenced the information posted here.I have no mechanical talent and was able to install the part without difficulty.

Gas oven would not light

  • Customer: Steve from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked the igniter resistance with an ohm meter. It read about 350 ohms. Voltage across igniter leads with igniter removed was 120 volts when the oven temperature control was turned on, so I knew the gas control and thermostat were ok. The new igniter has a resistance of about 220 ohms, so the difference was apparently enough to keep the oven from turning on. This is the second igniter I've replaced in this 20 year old oven, the first bad igniter had open resistance, obviously since it was visibly cracked. The repair went very fast, directions were great.

would glow but would not ignite

  • Customer: charles from Mount Prospect IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Turned off power removed racks removed bottom panel removed flame distribution plate removed igniter i didn't use -the wire nuts 'the wires on the new part were more than long enough so i installed new stake ons reveresd disassembly process turned power back on and now it works great with a factory look

old oven racks were nasty!

  • Customer: Richard from Fort Wayne IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

drawer glides broken

  • Customer: robert from toms river NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
poped out the old ones and new ones slide right in.

Storage drawer was hanging down.

  • Customer: Michael from Midlothian VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed the instructional video , removed the drawer, popped out the damaged part, inserted the new part, replaced the drawer. Didn't need any tools and the job took less than 10 minutes to do.

broken drawer glide

  • Customer: tom from duluth MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am a total non repairman. but with the video on how to I did'nt even brake the first part. ( I ordered 2 just in case)Will use you ror every part!
All Instructions for the TGF362BBBA
271-285 of 303