Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken fan blade in the freezer compartment
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Door wouldn't stay closed; fridge alarm went off constantly
I removed the door from the fridge by taking off the screws that held the top plate on. I then removed the old broken cam from the door and the old hinge pin on the fridge and replaced them with new parts. I then put the door back on, screwed the top plate of the door into the top of the fridge, and with a few minor alignment adjustments with the freezer door, I was done.
Disassembled front door/cover (3 screws), then removed deflection door assy, (4 1/4" nuts), CArefully and methodically removed C Clip and grinder teeth...Be careful with this step to document/remeber how to re-assemble! Auger repleced then reverse steps... All in all, not too bad, but you can easily screw up the teeth re-assembly.
I removed all items from area of refrigerator. I removed the drawers. I unscrewed the broken slide rail. Upper drawer had left side broken. Lower drawer had right side broken. I simply screwed the new slide rail in. The glass shelf didn't fit, so I took a pair of needle nose pliers and broke off a tiny piece on the slide rail that was preventing the glass from dropping in. (I checked the old one first and could see the same thing had been done) I screwed each rail in and dropped the glass shelf back in. (The lower shelf was broken and I ordered a replacement at the same time as the broken rails. I put the glass into the plastic holder of the old (broken) shelf and slipped it back in. Very easy. I'm a housewife not a repairman. I saved a few dollars on a house call.
Removed the top hinge and the door. Removed door stop held in place by 2 screws, installed new door stop. re-installed door and top hinge. Easy once the correct diagnosis was made It would have been nice if I could have e-mailed you the symptoms and received an accurate diagnosis. As it developed, I initially replaced the door cam before realizing that the door stop itself had broken.
Flat or philips screwdriver does not fit, Hex keys do not fit either. Had to buy a set of 6-pointed Torx keys to remove and re-install the existing screws. With the right tool it is an easy job.
This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!
Water line was broken at the bottom of the freezer door.
There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.
refrigerator wasn't cooling but the freezer was working properly
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Unit would not terminate defrost cycle resulting in melted frozen food
Turn of power to fridge. Removed all shelving in freezer section. Unscrewed back panel from freezer area. Removed old defrost term t-stat from top of evaporator coil assembly. Cut existing two wire leads, spliced in new T stat wires. sealed wire splices from water egress and clipped new t-stat in same position as old one. Reassembled rear panel, installed shelves. Turned power back on.That's it.
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.