TEF326FBC Tappan Range - Instructions

This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

Removed screws,pulled off clips,reinstalled new element.

Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

Just plugged it in! The hardest part was finding the model number. It was inside the top of the stove,while cleaning, I found it-on the left hand side when you take out the burner pans. I searched this site, found the part and when it arrived I just plugged it in and it worked fine. I would say less than 5 minutes to fix this issue.

pulled out the range and unplugged the range from the outlet! removed the oven racks. unscrewed the heating element and pulled out the wire connections a bit so i could grasp the connectors better and so they would not go back into the holes. getting the bad element off the connectors was the most difficult part of the process - this is what took the longest for me. I used pliers to grab the heating element connector and wiggle until it came loose from the connectors. once off, it was pretty simple to re-connect the replacement element and tuck everything back and screw the element back onto the oven wall. WA-LA!! back in the baking business - kids and mom are happy again! temp needs calibrating, but should be able to figure that out....thanks much!

Just unscrew the two screws that attach element to back of oven. Pull element toward door until you see push on terminals. Pull both terminals off.

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

Got the part,very affordable quick shipment,put it in plugged in the wires...Done! Thank you, getting parts from you for my ice maker as well!

- Cut the power to the oven (I used breaker). - Unscrew 2 screws. - Disconnect from 2 electric terminals. - Remove old bake element. - Connect new bake element to 2 electric terminals. - Screw the 2 screws back on. - Turn the breaker back on. ------------------------------------------------> Done! . . Saved the $79 that the appliance guy would've charged just for diagnostics. The part shipped to me within 24 hours so I didn't have to worry about scheduling a 2nd appointment and waiting around with no oven. You can do this on your own! Thanks partselect.com :)

Simple. Unscrew 2 screws unplug 2 tabs. Push on 2 tabs. Put 2 screws back adjust feet.

My husband did the repair he removed the old element and replaced it with the new one it was very easy to replace.