TEF326FBB Tappan Range - Instructions

Watched the video on Partselect before ordering the part, to see what I was getting into. Part arrived super quick. Removed bad element just as video described, and installed new element in opposite direction. Job was complete, and super was in the oven in less than 15 mins after arriving home from work. Anybody can do this repair, don't waste your money on a service call!

first pulled the breaker, then removed the oven door. One wire came out easily but the other side would not budge so we had to take off the back of the range. They had cought the wire up in a loop and so it had no give. Removed it from the loop so if it ever needs to be replaced again we won't have the same problem. Used the advice from other comments and it went as discribed. I hope others also removed the door as I can't imagine how much harder it would be with the door in place.

Real easy to replace the heating element. Two screws and out came the old and in with the new one.

I had the part shipped directly to the rental house and the tenant installed it with no problem.

after reading the very first reader report, I was happily amazed how easy the repair was. it took longer to unwrap the part than it did to undo two small nuts, unclip the wire, clip on the replacement burner, and redo both nuts. thanks again for the help. saved lots of time and money.

I had to remove the back of the range in order to cut away the sheet metal that was contacted by the bent terminals that had to be done to shorten them to clear the back sheet metal panel.

took the two nuts off the back wall of the stove and disconnected the push on terminals. ordered by model number. replaced and reinstalled the two nuts in stove. simple as possible

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

It was just a matter of loosing 2 screws on baking element & pulling 2 wires off & putting back on. On the Burner I had to take 6 to 8 screws off back 4 wires off & 2 screws on fron of switch. Very Easy!

The drawer dropped down and would not easily open or shut or fit up good when closed. A quick inspection showed that one of the rear drawer guides was broken. The parts were ordered on a weekend and they showed up on Tuesday. We already had the pots and pans out of the drawer. It took about 10 minutes to put in the new guides (I replaced the one not broken also), clean and lubricate the drawer slides. Good as new. The repair video, although not necessary for this repair, was excellent. Thanks a bunch!

take back planel off, take wires off old element and intsall new element hookup wires, put back planel ..under one hour job

just slid drawer out all the way clipped new parts into place and reinstalled drawer-less than 1 minute to complete entire process-online store was very easy to use,great parts breakdown/pictures helping to ensure proper part selection/quick delivery/will be back for more parts when needed in future and will recommend your site to my friends

took off back cover unhooked wires. pulled out screws in the oven and removed the element. put in new element replaced screws reattached the wires in the back replace the back cover. Done

I followed the Parts Select Video that showed replacing an identical switch. Mine were another brand & style with different color wires. I took a picture of 1 to keep track of the wiring and removed it. I saw that the terminals were marked P, H1, H2, L1, & L2 so I put the wire from the same terminal onto the Parts Select switches & they work just fine now. The parts I got from you are heavier and a much better quality than the original equipment. I would also like to say that I was amazed at how fast this order was shipped, and the washer pump was a piece of cake thanks to your video.

No directions come with the parts. I used a nut driver to unhook the connections on each side. The wire was connected with a male/female small connection ( they were inside the back of the oven. I pulled each one out and had to pry them loose with a screw driver. I attached each wire and used the nutdriver to tighten them. It was easier doing the repair than writing this explanation. I am not a handy man...