TDB210RFB4 Tappan Dishwasher - Instructions

First I unplugged the diswasher, than I unscrewed 4 screws on the inside of the door which pops the door off, unplug two wires, note which one goes where, unscrew 6 screws that holds dispenser in place, than reverse order to install new part. Very easy.

First I read the online bog's such as this one, those instruction said it was an easy task to pull out the old gasket from either side and then push in the new gasket in reverse of removal, in from either side, but the only way the gasket can be installed is to lay it along the channel it is to be installed in and then push it upwards. Due to all they butter and grease that gather's on the edges at the bottom of the door it is nearly impossible to slide it in place, so to push it up is the only way that will work!

Took off all the screws, replaced the dispenser-no problem. However, I couldn't get the top to stay in place long enough to get the screws back in. My boyfriend came over and couldn't get it together without using a longer screw in the top area. Now it works great.
The only other problem was my bank and my VISA-they both called me stating my account was being used out of the country. They issued a fraud alert at first, but I called them and told them everything was fine.
Linda
Florida

remove two small screws and slide the dishwasher out, lean it back and see where the water was leaking out. turn of the water remove water supply line and remove the water supply valve. then went to partselect.com and ordered new valve. the dishwasher is now like new for only $21.86 and UPS left the valve at my door in about 4 days::::LIFE IS GOOD

*Shut off power to dishwasher at circuit breaker (hot water supply had already been shut off under sink since inlet valve was broken and was allowing water to run into washer nonstop)

*Removed front lower panel from dishwasher

*Removed valve assembly from dishwasher frame

*Disconnected wiring harness from valve

*Disconnected incoming water line from valve

*Disconnected outgoing flexible water line from valve

*Installed new valve in reverse order

It was a pretty easy installation other than the small work area under the dishwasher.

I simply opened the door all the way and used pliers to grab hold of the old bottom gasket and slid it out sideways. Then inserted the new bottom gasket into the slot and pushed it in. No leaks for the new pergo floor. Half the battle was realizing that this thing was in there to begin with. It is a long thin plastic flap with a rubber strip on both sides not reallya gasket per say. Fast delivery and great instruction from other customers.

pulled out old seal replaced with new one very simple

Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.

removed old gasket by hand, installed new gasket with hands only. p.s. great doing business with you,thanks.

Had a leak, due to the factory gasket was 1/2 " to short. Pulled out old one, installed new one, and trimed to fit. Took less the 5 minutes.

At 1st gasket kept going in to far, but after a few tries an my wifes help it went in. I had trouble with the adjustable legs as the floor was tiled an rasid up, but all in all everything went good. Ran it a few times on rinse. We're ready to go. Richard

pulled the old gaskets out, put the new ones in. Just like that. No tools, nothing. I would compare it in difficulty to the process of paying for gas at the pump and then filling your car up.

The 'kick plate' had to be removed, and the feet had to be raised to lift the unit over the floor. the old spring could not be found, and while lying on the floor my husband had to 'feel' for the attatchments to hook up the new spring. The unit was then pushed back and the legs dropped and the unit attatched to the counter. All fixed - - thank you PartSelect for having the right spring.

Turn the water off to the dishwasher. Loosen water supply connector w/ crescent or sized wrench. Remove bracket srews from water inlet. Remove spring clip from discharge hose, remove hose from discharge nipple. Replace with new part in reverse order.

Shut off water, unpluggewd appliance, removed two screws holding part in place. Removed water supply hose from part to Washer, remover water supply from source to part. Reversed steps with new part. DONE! I'm not handy at all it was mostly luck diagnosing problem.