TAA600 Amana - Instructions

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Removed front of control panel on the washer. Found the lid check switch, removed one screw, leaving the wires attached and replaced the old switch with a new one. Removed the wires from the old switch and place them on the new one. Reconnected the machine to the outlet,,closed the lid and listen to it run.

Changed lid switch. The hardest part was to remove the old switch. Wire connectors were very tight on the connection tabs of the old switch. Just out of curiosity, I did take the switch base plate apart just to see what the lid lever looked like underneath and how the adjustment worked.

Based upon my research on line and my 'hunch' I ordered the Lid Safety Switch for this old Maytag Washer. Got the part in good time and it was very well packaged. After having some difficulty in removing the one nut that held the old switch in place I installed the new switch, plugged it in and was delighted to hear the washer working like the old days. Now I have many, many loads of clothes to catch up on.

Removed the cover on top raised control panel at back of machine. Checked fuse, then lid switch which were okay. Checked Check-lid switch which was bad. Ordered and replaced. I always take pics with cell phone before removing anything to see position, wire colors, etc. Only difficult because of location on check-lid switch. Hard to reach even with right angle screwdriver. Had to bend some of the metal housing above the switch to get screwdriver in there.

It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.

Followed above listed advice on replacing

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Checked the fuse it was blown. So I replaced it, pluged the washer back in. pull the start knob that's when the lids switch sparked and blew the fuse again.
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!

Taking the hub out was a promblem because, with a puller it did not come out. It broke off while pulling out we had to drill it
out had to brake off.You need a 1 1/2 inch deep socket with a impact wrench. It was a hassel but got done. I replaced the whole seal kit and it is still leaking it leaks from the bottom of the tub. It leaks worse when it has a heavy load I dont know what to do.Need help.

Very easy, and simple. Replaced part that was sent. It was a simple process, open control panel, unplug machine. Unscrewed the old part, attached the new part and starting working right away. I am very impressed with this company and the speed they shipped the parts. Will continue to use if needed and tell everyone about this site.

Hi there,
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.

Thanks,

Harry Lin

I called a local repair service and they wanted 95 bucks for the first 30 minuets. Any thing over that was an additional 45 bucks per half hour, plus parts. Since the washer was 19 years old I thought it would cost around 300 big ones to get it repaird. We could buy a new similar model for about 550 bucks so I said, what the heck. I'll invest the 18 bucks to see if this 80 year old can fix it. The repair instruction I read on your on line were perfect. FIXED IN ABOUT 20 MINUETS.Installed the lid switch, saved a bundle and maybe another 19 years on the washer. Thanks a bunch. Walt Apple Valley Mn

Removed the old pump and installed the new one, works great!

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.