Models > SVD48600P Maytag > Instructions

SVD48600P Jenn-Air Range - Instructions

All installation instructions for SVD48600P parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600P
196-208 of 208
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

WHEN WE TURNED ON THE OVEN THE TEMP. READING WENT UP TO 425 AND BEEPED BY NO HEAT

  • Customer: DAVID from Cape Coral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back WOW saved me $500. from buying new and $150. for service call

change oven sensor

  • Customer: Lloyd from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Oven have F2 and F3 codes following cleaning cycle making oven inoperable

  • Customer: Timothy from Longmeadow MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Range had an F-2 code on the control panel

  • Customer: Greg from Frederick MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Oven would overheat

  • Customer: MARK from roseville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Front burners would not light.

  • Customer: Jeffrey from Columbus GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.

F5 fault code kept appearing

  • Customer: Louis Rodriguez from Granbury TX
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

the grease filter was no longer usable from too many washings

  • Customer: Rose from North Kingstown RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took it out and dropped in the new filter. Total time about 2 minutes

rear burner not working

  • Customer: Larry from Washington NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
removed two hexigon screws--removed old burner---placed new burner into stove socket--replaced two screws. Done in about five minutes. Most time used to fine right size socket to fit screws! Fast delivery--easy repair--AND it works!

Bake element burned

  • Customer: Larry from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned of the power, removed an old element, by unscrewing 2 screws, pulled out element out about 4 inches, remove the slide on connectors, then put them back on that new element, carefully slide in element to the back wall and screw in the 2 screws. Turn the power back on. It is nothing to it. When the old element is out, I took an advantage and cleaned up the inside, using the oven cleaner sprayer.

broiler pan missing

  • Customer: RAYMOND from JACKSONVILLE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ordered new broiler pan
All Instructions for the SVD48600P
196-208 of 208