SK525-2W (PSK525200W0) Maytag Refrigerator - Instructions

This was an easy fix. Just pull off the old gasket and press the new gasket in place.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Remove plastic hinge cover (phillips screwdriver). With door closed, remove ground wire (phillips screwdriver). Remove broken hinge (nut driver). Route wires through split in hinge body. Route wire through new hinge body. Install new hinge (nut driver). Install ground wire. Install plastic cover. Entire job took less than five minutes.

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Put the new one in its place easy

Grind rivet head off , install rivet tap end

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

My husband took the door off and replaced the door closure cam kit with no problem the door opens without a sound.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

Was a very tight fitting part and it had to be gently tapped into place.

1. Removed part from packaging. 2. Cleaned part with foodsafe cleaners. 3. Rinsed thoroughly. 4. Dried thoroughly to prevent frost. 5. Placed bin in freezer. 6. Turned on ice maker. 7. Waited. 8. Discarded first batch to clear supply line. 9. Waited. 10. Enjoyed ice. 11. Provided these inductions.

Ordered part...removed old drawer...put n new drarwe

I am completely satisfied with PartSelect Appliance Parts. I had a broken vegetable drawer in my Amana refrigerator and had delayed fixing it because I thought it would be difficult. Finally I got the model number from the door sticker and Googled it for where I could find the part. PartSelect came up and I was amazed at how easy it was to locate the correct replacement item and how easy it was to place the order. Then much to my amazement, the part arrived in 2 days and in perfect condition because it was shipped with all precautions against damage. I removed the broken drawer, pushed in the new drawer and voila! All good. I highly recommend PartSelect Appliances for their user friendly web site, their ease of ordering and their super fast shipping. Thank you!!

pulled the old one out and slid the new one in. Even I did this right. If I can do it anyone can do it. The only thing I worried about was if I ordered the wrong Crisper Pan.