SF315PEPW1 Whirlpool Range - Instructions

Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!

Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

It only took my husbend 6min to put in the new oven igniter. But it did not work, so I call your center and the rep there talk my husbend and told him how to unluck the key bord, and that worked. Thank you for all the help.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem