SER341AQ1 Westinghouse Dryer - Instructions

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

I have used this company twice now and both times have been a good experience. Would highly recommend!

Many thanks for the video you guys put together on replacing dryer belts! I didn't know how I was going to get inside the dryer. I had the dryer apart in 10 minutes! Had to wait a day for the belts to come in. New belt in and dryer running in 15 minutes! Thanks for running a first class operation!! Jim

Did it just as the Video said to and had no problem other than it should have warned about a possible problem with the Drum drive belt going to pieces. I am very happy with PartSelect for the parts and the instructions, it all worked well for this "Old Man". Thank You p.s. My local Sears had the belt or I would have gotten it there too

I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

Could not figure out how to get into the dryer. Wasted a couple hours trying different things. Found a video online which showed the repair I wanted to make. After that it was easy. One needs to be tall and in shape to lift the drum out of the case....or have the help of a second person. Only a little blood was shed but now feel confident I can replace any of the parts in the dryer if needed.

put door catch in hole

Followed your very helpful video instructions. Saved me a ton. Five stars!

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.