Models > SER341AQ1

SER341AQ1 Westinghouse Dryer - Overview

Get Parts and Repair Help for SER341AQ1

If you know the dryer repair part you need, you can browse the list of all parts on the SER341AQ1, or you can search by name or part description. You can also find your part by where it is located on the SER341AQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for SER341AQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.


Drum Belt

This 87-3/4" long dryer drum belt goes around the dryer drum and the pulley to rotate the drum once motor is activated.


Drum Glide - White

Appliance requires 2 .Sold individually.


Drum Support Bearing

This part attaches onto the inside of the rear panel of the cabinet.


Heating Element Assembly

This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.


Thermal Limiter - Limit 220

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.


Door Catch

This part helps keep the door closed while the machine is running.


Lower Front Felt Seal with Adhesive


Front Upper Felt Seal with Adhesive


Lint Filter

This white dryer lint filter screen collects lint as it passes through the dryer vent.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 269 of 277 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

short circuit with a brasier metal support

  • Customer: Juan Carlos from Weston FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 179 of 209 people found this instruction helpful
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear m... read more

Thermal Limiter opened

  • Customer: Stephen from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 174 of 227 people found this instruction helpful
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works. read more