SCE4340B-C Jenn-Air Range - Instructions

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

Removed the 4 screws on the bottom of the panel, lifted the panel out and up to clear the uper part of the panel. Removed the screws from the left and right switches, which hold the bracket of the clock, marked the wires of the clock and removed the wires. Installed the new clock in reverse. The power to the range was off.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

The front burner the large one was burnt out, I cook alot so I need it, I happen to see a appliance repair man next door. I describe problem and he said well figure about 250 - 300 hundred dollars. 80 For the aprt the rest labor and house call. Well I looked at the booklet and figured out what I had to do ,needless to say I owent to your website and you had the exact part I needed and saved me alot of money. I sugest to d. I. Yers try it and if it doesn't work then call the repairman. Thank you parts select. Glenn voight

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

I first bought an oven thermometer to check temperatures at different levels. Temperature was about 10 or more degree off. I next looked at the manual and found you can make an adjustment to the temperature knob. This didn't make a difference. Decided I would replace the bottom heating element. I ordered and got the element in a matter of days.
The hardest part was loosening up the screws on the bracket for the old element. Thus the use of the vice grip came in handy. My oven is 20 years old!!! I'm sure I saved my husband a couple hundred bucks worth the repair guy.

My thanks to "Part Select" for making the process so easy to order and get a replacement. The repair guy finally called yesterday. Five days after I repaired the oven myself.

Go Girls, you can do it!!!!!!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

This was obviously not a hard repair, I just replaced the knob. I would like to say that I did receive the part in just a little over 24 hours. That was nice!

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.