Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV205DAWW

SAV205DAWW Maytag Washer - Overview

Get Parts and Repair Help for SAV205DAWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV205DAWW, or you can search by name or part description. You can also find your part by where it is located on the SAV205DAWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV205DAWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

$27.04

Brake Pad Kit

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

$105.11

Triple Lip Seal and Bearing Kit

Please check your model# to verify this is correct for your appliance.

$19.05

Standpipe Adapter

This part helps stop the washer from overflowing.

$124.51

Triple Lip Seal and Hub Kit

NOTE: Before ordering, please make sure this is the correct kit for your appliances Model#.

$28.58

Friction Ring

Plastic Washer

This washer is located between the brake and transmission drive pulley.

$4.79

SPRING- CO

$29.57

Spin Pulley for Transmission Drive

This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 163 of 187 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Spin cycle sounded like freight train

  • Customer: Mike from Houston, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 78 of 85 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

Drive Pump Leaked

  • Customer: Stephen from Laveen, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 66 of 78 people found this instruction helpful
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screw... read more