S5200E6WW General Electric Washer - Instructions

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

Watch the videos you might be a little skeptical at first. I watched the videos about 8-10 times before I bought the part so I took my part out first then got back on you tube watched a few more videos and got on parts select website found the part matched it up to what I pulled out of my washer ordered it got to me in a weeks time put it in and working like new again cost about 14.00 shipping and part together saved about 200.00 per my estimate I had to fix it.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

Removed the front of the washer using a putty knife. Removed the old belt and used a shop-vac to c,San up the insides. Placed the belt on the pulley and used three med sized zip ties about one inch apart. I cut off the exposed tail of the zip ties. Got the belt started around and put the belt onto the small pulley. Keeping an eye on the small pulley to make sure the belt did not slip off, I had to push it up a time or two. Then as I pulled the big pulley around, one zip tie broke, replaced it and continued pulling the big pulley, it got tough but with one knee pushing on the drum and pulling with one had it went on. I did slowly turn it to align the belt on the big and small pulleys. Not hard, I recommend a bright flashlight and gloves. I saved a good buck doing it myself :-)

REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

You tube is the only way to go!

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.

Followed the video guidance supplied by this site

I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.