S160 Jenn-Air Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven door seal needed replacement, filters replaced
First we removed the door from the stove. Removed all the screws and removed the damaged seal. We replaced the seal and re-assembled the door.
Parts Used:
-
Michele from Stafford, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
17 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broiler element had burned intwo.
I removed the back of the stove for easy access to the wiring (three hex head screws) and removed the two wire leads. Then I began to remove the mounting screws from the inside of the oven, the first three screws came out fine the last one was so tight that I had to resort to vise grip pliers. Jenn-Air should have used hex head screws instead of phillips head inside the oven. Finally after about 15 minutes the last screw came out. I installed the new element, reinstalled the screws and wires. Then I replaced the back and tested. Total about 45 minutes.
Parts Used:
-
Lynn from Louisville, KY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken switch would not turn on exhaust fan
Removed 2 screws to get to old unit, unplug electric wire and pluged in new switch.
No problems, correct parts. Will look for other needed parts in the future.
Thanks
No problems, correct parts. Will look for other needed parts in the future.
Thanks
Parts Used:
-
Don from Nacogdoches, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven fan/ight switch broken
The hardest part was removing the old switch. It had locking washers that were very hard to remove. After that it was a breeze. Be sure to turn off the electricity to the oven.
I'm sure I saved a ton of money and wife was ecstatic, it had been broken for a year or more.
I'm sure I saved a ton of money and wife was ecstatic, it had been broken for a year or more.
Parts Used:
-
Marc from Maineville, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Parts Used:
-
alphonso from plainfield, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan and oven light would operate.
Removed the old part by removing the clips and wire connectors. Then placed the new switch in place and reapplied the wire connectors. Tried to then place the new clips on the posts but the clips were very fragile and they broke. Then decided to thread the posts and use nuts. Used a minature die to thread the posts, applied washers and nuts and finished the job.
Parts Used:
-
Larry from Portland, OR
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
not a prblem,just necessary to replace
even though these sre washable filters it's still necessary to change them after so much time
Parts Used:
-
Peter from Wilson, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
grease filter did no fit much to large
switch went well
removed 4 screws and lifed front panal up and out
removed 4 screws and lifed front panal up and out
Parts Used:
-
charles from Newton, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element started on fire
My husband and I couldn't believe we were able to do this!!!So easy! We were dancing around the kitchen!!!!! We credit the advice of other do-it-yourselfers. Very accurate and true. It took less than 10 minutes after the screws were WD40'd. In addition, we recommend: use a flashlight to see in the oven since it's dark with the power cut off , and use this time to clean behind the stove!!!!!
Parts Used:
-
louise from cedar urg, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very Easy Repair
The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.
The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).
After that, re-assemble the door and drop in place. It was a snap.
FYI...the shipping was ultra fast and the price was great.
No issues whatsover with the entire process.
The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).
After that, re-assemble the door and drop in place. It was a snap.
FYI...the shipping was ultra fast and the price was great.
No issues whatsover with the entire process.
Parts Used:
-
Donald from Edmond, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old switch was difficult to remove and the push nuts provided with the new switch were too small to fit on the lid posts.
Removed the old switch by essentially destroying it with a screw drive and pliers. Had to drive to the hardware store to purchase push nuts that fit.
.
.
Parts Used:
-
Chris from Wellesley, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Parts Used:
-
Ivanka from Atlantra, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Malfunctioning Switch on Jenn Air D156W
Just wanted to thank you for the great service. I ordered the part on Tuesday, it shipped on Wednesday and arrived on Thursday. I installed the switch in under :10 minutes on Friday and the old Jenn Air grill is running like new again.
Many thanks!
Many thanks!
Parts Used:
-
Mark from Coconut Grove, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front burner stayed on high
We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!
Parts Used:
-
Natalie from North Reading, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench (Adjustable)
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Parts Used:
-
William from Schwenksville, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!