Models > RVM1435WD001 > Instructions

RVM1435WD001 Hotpoint Microwave - Instructions

All installation instructions for RVM1435WD001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1435WD001
31-45 of 395
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No heat in the microwave

  • Customer: Douglas from Mechanicsburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 19 people found this instruction helpful
We purchased our Microhood oven about 4 years ago along with the extended warranty package offered thru home depot. Within one year, the problems began. Each year the secondary switch would go bad rendering the microwave useless. If you have 3 small children like we do, you tend to use it a lot. We sure take the microwave for granted.

Each time G.E. would fix the problem at no charge. Ths time - the warranty had expired and GE wanted to charge us $80.00 for service call plus parts and labor. We estimated the cost to run at least $150.00 or more.

To top it all off, GE was going to have a service tech avail for over 2 weeks. This is poor customer service and completely unaccceptable.

Because this was a recurring problem, I figured it was the same part that had being going bad since we purchased the appliance. I decided to order the part "secondary switch" myself and attempt to fix the microwave on my own.

I ordered the part last Tuesday, the part arrived last Friday. Within 10 minutes I had the microwave apart, replaced the part and had the microwave back in working order.

PartSelect saved me over $100.00.

We are very satified with PartsSelect, I would recommend them to anyone

A horrid grinding noise while using appliance

  • Customer: Gordon from Norton MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 16 people found this instruction helpful
I looked up the parts of the microwave on Part Select to see if there might be something I might be able to do myself. I found that the Cooking Tray drive motor was the problem. I ordered the part and got it the very next day. I loosened the 6 screws to the lower part of the microwave and then the two screws that held the part in place. I removed the element and pulled the wire plug from the element, placed the new element back in with the screws, repluged the wire, placed the lower cover back to the microwave, tested the microwave out and, is still working quietly as if it were new. Thanks to part select.com it was easy.

repair broken lens and replace light bulb.

  • Customer: Heidi from Astoria NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
This was a super easy repair job. I couldn't figure out how the lens that covered the light bulb would have cracked and realized it must have been from my contractor when he replaced my stove. I can't prove it, of course, so I am left doing the repairs. The website was very easy to order from and confirm that I had the correct parts as the model numbers tend to change over time.

We had a crack in the control panel frame.

  • Customer: Catherine from West Chicago IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
The repair was simple. It was just a matter of removing the upper vent grill to access the screws for the panel frame. Then I just popped out the old frame and installed the new..and the micowave is as great as it was new. The PartSelect website allowed me to see a visual map of all the parts of my microwave which allowed me to find and choose the right piece for the job. It only took 5 minutes for the repair.

rotating glass tray was grinding and not turning.

  • Customer: Michael from Midland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
I first took the filters of the exhaust and then removed the screws on the bottom of the combination microware hood fan. Once the 6 retention phillips head screws were removed from the bottom of the microwave, and the hinged bottom "door" lowered the motor was exposed. I removed the motor by removing the two phillips screws and unplugged the motor. The hardest part was finding a replacement on the net because most shops did not give enough details or pictures to know if a part was exchangable or a replacement. Partselect.com listed the parts, motor voltage, and had pictures so that I was comfortable with ordering. The part arrived the day it was scheduled to and I simple reversed the process and within 5 minutes I had the microwave motor in and back together. It is nice to do business with a place that also gives you a returns policy upfront.

door handle broke

  • Customer: Charlene from Farmington UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I used the kitchen knife to remove the inside cover on the door. There are tabs which hold it in place along the vertical sides. Then removed the two screws holding the handle in place and replaced it with the new handle. Replaced the inside door cover. Thanks for the tip on using the knife to remove the inside cover!! It was easy!

Cooking Tray motor failed

  • Customer: kEN from Southborough MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Found this site, was able to identify the specific part through the internal search engine, very user friendly.

Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!

If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.

Great site, great resource, super fast shipping.

both lights burned out

  • Customer: Rick from Federal Way WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
After reading some of the comments that others wrote, I decided to order the light sockets along with the replacement bulbs. As predicted, the old light bulbs broke when I tried to remove them - the bulb separated from the base which was still screwed in the socket. After removing the screws that held the bottom panel, I was able to remove the socket assemblies with ease. After inspection of the old sockets, I was glad I ordered new sockets - the old sockets were burned in some spots and very brittle. The parts arrived within a day and a half after I ordered them, but when the parts arrived, one of the bulbs was broken (happened during shipping). I called the office phone number and talked to a really pleasant technician who refunded me the price of the broken bulb and placed an order for a replacement. That was the Wednesday evening before Thanksgiving Day. I got the replacement bulb yesterday (Tuesday) morning - still really quick considering the Thanksgiving holiday. All of the parts are installed and are working excellent. I am definately going to keep their WEBsite for future use, and I'll be letting my friends know about them. Thanks PartSelect, you've earned my business.

Old cooking tray drive motor no longer worked.

  • Customer: JAMES W. from Parkland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
After finding the part on PartSelect, ordering it online, receiving it quicker than expected -- it took me 5 minutes to unscrew the bottom cover of the microwave, take off the old motor, replace with the new motor, screw the cover back on and test the WORKING cooking tray drive motor.
Very impressed with the efficiency of PartSelect. It's web page was easy to navigate. Thanks.

Replace Door Film

  • Customer: Roy from Alta Loma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 25 people found this instruction helpful
remove old film, apply new film. real easy. no magic

GRINDING NOISE IN MOTOR

  • Customer: MARK from VALLEJO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
REMOVED UPPER COVER. REMOVED SCREWS IN COVER PLATE & MOTOR MOUNT. REMOVED INNER COVER WITH POP SCREW INSIDE MICROWAVE. REVERSED PROCEES TO INSTALL NEW MOTOR.

No power to microwave

  • Customer: James from Highland UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 17 people found this instruction helpful
Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.

Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.

Broke light fixture socket

  • Customer: Norman from Benson NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

Oven blows 20 amp fuse

  • Customer: PATRICK from Covington LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Light socket replacement

  • Customer: lester from orlando FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.
All Instructions for the RVM1435WD001
31-45 of 395