Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
61-75 of 176
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

detergent dispenser would not operate

  • Customer: Lee from Thomaston, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 12 people found this instruction helpful
remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Leaking Dishwasher

  • Customer: Althea from Vancouver, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Water leaking from pump seal.

  • Customer: Jasper from Opelousas, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 2 of 4 people found this instruction helpful
After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

soap dish door does not always pop open

  • Customer: John from Dubuque, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 7 of 19 people found this instruction helpful
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

My Dishwasher Started Leaking Out The Bottom Of The Impeller Assembly.

  • Customer: John from Eldersburg, MD
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 16 people found this instruction helpful
I went on line and found the partselect website and was able to identify the defective parts using the schematic drawings. I ordered the parts and in about an hour I had reassembled the dishwasher and had it running again much to the joy of my wife and children. (No more washing dishes by hand!). I also purchased the touch-up paint and tine tips and now the washer looks and runs like it did when I purchased it.

Water leak from the pump housing.

  • Customer: Steve from Mount Pleasant, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I removed the three screws holding the motor on the housing. Then I took the two hoses off and from inside the washer I unscrewed the ring at the base of the wand that holds the housing in place and removed it. I then replaced the impeller and seals and reversed the process to put it back together. Cost me 26.00 for parts and shipping. I couldnt imagine what anyone else would have charged. I will do business with PartsSelect again in the future.

Broken Access panel

  • Customer: Frank from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Part arrived in 48 hours. Had to pry apart the two piece assembly of the damaged item. Snapped the replacement in place and fastened it to chassis with two machine screws

Soap Lid Pin Broken

  • Customer: Robert from Port Clinton, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 11 people found this instruction helpful
Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.

The access panel below the dishwasher had broken loose from the upper screws.

  • Customer: Preston from Atlanta, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
The panel was removed by removing the lower screws and lifting the panel out. The old panel had a wood insert to match the cabinets in the kitchen. I removed the upper plastic piece holding the wood in place and slipped it out. I inserted this into the new access panel and attached the upper plastic piece to hold it in place. I detached the metal vent piece from the bottom of the old access panel and snapped it into the new panel. I then slipped the metal vent over the lower screws and tightened them. Finally I inserted the upper screws and tightened the panel into place. It took less time than I expected and only required a nut driver and a screwdriver.

changing a damaged door panel insert

  • Customer: Constance from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!

Upper dishrack needed replaced

  • Customer: Scott from Wichita, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

Door seal leaked and wash arm bearing broken

  • Customer: Glen from Harrison, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 2 people found this instruction helpful
The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.

Water leaking on wrinse cycle.

  • Customer: Charles from Buckner, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.

water leaking from door

  • Customer: tim from loganville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

The corners of the panel were the screws hold the cover onto the appliance had broken.

  • Customer: mike from Auburn, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
When the new part arrived I had to swap over the bottom metal plate that secures the bottom of the cover and also had to swap over the decorative front plate and top edge. The part worked wonderfully the job was very easy. The only thing I forgot to check on was the color of the part. I needed white and I ordered black, but that also was no big deal as the covers from the old part was white and covered it up. I will be using Partselect in the future and would recommend them to friends.
All Instructions for the RUD5750HB0
61-75 of 176