Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
76-90 of 176
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Tines where falling off old rack

  • Customer: RONALD from EAST GREENWICH, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 12 people found this instruction helpful
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

slow leak at motor/pump interface

  • Customer: Donald from Webster Groves, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.

Wheel on lower rack broke.

  • Customer: Martin from Union Bridge, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 3 people found this instruction helpful
New one snapped right into place.

pump seal and impeller

  • Customer: David from Lisbon, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 1 of 3 people found this instruction helpful
had to replace the insides of a leaky pump

Water leaking from front door of dishwasher

  • Customer: Gregory from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

Cap did not stay in the hole any longer.....was melted

  • Customer: Debra from York, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!

water leaked through door gasket.

  • Customer: Charles F. from Burnet, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Lowered door and put a weight on it to keep it open. with screwdriver pried out the old gasket. It was simple. looked at the end of the replacement gasket and inserted it into the track with the small hole down. Job Complete. about three minutes total time.

leaking around door

  • Customer: john a from west seneca, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
1-2-3 EASIEST JOB I EVER HAD to DO AND THE WIFE IS PROUD OF ME FINALLY.

THANKS , , ,Bat from WEST SENECA (Buffalo, NY)

Dishes would'nt come clean or dry from torn boot

  • Customer: David from Sallisaw, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 10 people found this instruction helpful
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

The door leaked during wash cycle

  • Customer: John from Frankfort, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

Water Seeping From Under/Around The Door

  • Customer: Nate from Fort Worth, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I opened the door and pulled the gasket from around the dishwasher. The gasket does not have any adhesive around it, so it pulled free almost immediately. The new gasket was pressed into place around the door and I was done. It couldn't have been any easier. I suspected it was the gasket when I saw pinched portions that did not return to the original shape and there were no visible cracks in the machine.

The corners of the panel were the screws hold the cover onto the appliance had broken.

  • Customer: mike from Auburn, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
When the new part arrived I had to swap over the bottom metal plate that secures the bottom of the cover and also had to swap over the decorative front plate and top edge. The part worked wonderfully the job was very easy. The only thing I forgot to check on was the color of the part. I needed white and I ordered black, but that also was no big deal as the covers from the old part was white and covered it up. I will be using Partselect in the future and would recommend them to friends.

Front door panel was missing

  • Customer: Crystal from Bowman, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed the cardboard insert, put the new front panel on and replaced the tabs. That was it!

The access panel below the dishwasher had broken loose from the upper screws.

  • Customer: Preston from Atlanta, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
The panel was removed by removing the lower screws and lifting the panel out. The old panel had a wood insert to match the cabinets in the kitchen. I removed the upper plastic piece holding the wood in place and slipped it out. I inserted this into the new access panel and attached the upper plastic piece to hold it in place. I detached the metal vent piece from the bottom of the old access panel and snapped it into the new panel. I then slipped the metal vent over the lower screws and tightened them. Finally I inserted the upper screws and tightened the panel into place. It took less time than I expected and only required a nut driver and a screwdriver.

Broken Access panel

  • Customer: Frank from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Part arrived in 48 hours. Had to pry apart the two piece assembly of the damaged item. Snapped the replacement in place and fastened it to chassis with two machine screws
All Instructions for the RUD5750HB0
76-90 of 176