RUD5750DB4 Roper Dishwasher - Instructions

used a common screw driver. took the ends off then pulled out the basket . used the screw driver to pop the brackets with wheels attached. new ones back on and about twenty minutes done. very easy.

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

I followed the video's from Parts Select and it took me less than 3 minutes to replace these parts. I did find it easier to use a screwdriver to lift the u shape of the spring over the detergent cup as the pliers tended to pull on the spring too much. Couldn't have been easier or faster, awesome!

Instructions very easy to follow

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

we followed your instructions submitted via e-mail and they worked out just fine....thank you

The broken access panel was VERY TIGHTLY engaged to the metal vent. After much tugging and pulling, trying to get the vent free of the broken access panel the two apart (without success) I used a large flathead screwdriver to split the portion of the access panel (its plastic) that held to the metal vent. Once the vent was free of the old panel, it could be easily snapped together to the new panel and this new assembly was held in place with two screws.

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

I removed the top dishrack by removing the front clips(stops) on the tracks. Then I removed both tracks by removing the back stops. Then I replaced 7 wheels. Then I replaced the tracks, dishrack and the front stops. The whole job took about 20 minutes.

The bottom trim piece popped off easily and I removed the damaged panel and replaced it with the new one. I snapped on the trim piece and I was done. It took less than five minutes.

Popped the old wheel mounts off with a screwdriver & put the new ones on.I was so proud of myself.I'm over 60 & a woman.The only thing my husband had to do was turn the rack around because I had it in backwards.It was so easy & incredibly fast service. My dishwasher is over 10 years old & I thought I would never still find parts but there they were.I will always use these people & will recommend them to everyone.Thanks so much.Sharon.

Watched your video and replaced seal in approx. 5 minutes, probably less. Still leaked so I looked at your page for solutions, found out where the air vent was and pried it open, very disgusting mess. With screw driver and long tweezers dug out what I could then poured a mixture of bleach and water in the vent. Totally cleaned it, very white, vent cover went into a bucket of bleach and hot water and it cleaned very well. Put vent cover back on and did a load of dishes, works fine. Thank you for having such a great website, if I ever need help again I will be back. It's a shame someone didn't tell you about cleaning the air vent when you bought the dishwasher.

Put the new part on

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!