RT21LMXKQ09 Roper Refrigerator - Instructions

Searched internet until I found a company(yours) with the part needed. Could not locate locally refrigerator too old. After finding"Part Select" site I watched the video provided. It was very instructive and helpful. I cancelled calling any repair service and did the repair myself. The part was delivered fast and I had no problems with the repair. Your confirmation e-mail of part being shipped again provided the video for the repair. I only watched again after the repair to check myself, all went well. My Ice maker is working great again and I consider this purchase money well spent. I was considering another refrigerator but will now keep the Kitchen aid longer, Thank you.

Just removed old ice maker which took about 2 minutes. installed new ice maker in about two minutes. Simple and easy install.

Ordered new set and installed

Straight forward.Vey easy to do

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

I removed the 3 screws but also removed the front screw of the left bin rail. This gave more room to maneuver I/M into position. The cover shown with the enclosed instructions does not show an Ice Plus (blower assy.). By removing the two mounting clips fron old unit and snapping on new one blower unit fits as original. Overall a very simple and quick repair. Note: None of the cables Inclosed were used as my harness does not unplug from wall. Thanks for the quick service PartsSelect.

We thought that the problem was with the inlet valve, perhaps dispensing too much water and causing the overflow that caused the leak. Installation of the valve was easy, but it didn't fix the leak. After some more tinkering, we discovered that the problem was that the ice maker itself had gotten out of kilter, that the rear part was tilted down too far and was causing the overflow that created the icicle. The rear part of the unit needed to be raised by adjusting the rear screw that attaches the ice maker to the refrigerator. Easy to fix that, and so far, no more leak. It didn't hurt, though, to get a new valve and be forced to clean out the back of the fridge, as well as replace the copper water inlet tube with a plastic one.

Turned off circuit breaker. That turns off both power and water. No need to move refrigerator. I backed out the 2 top screws about a quarter inch and then removed bottom screw with a quarter inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection. The new Ice Maker was wired correctly for my refrigerator so all I had to do was reconnect the power connection and mount new Ice Maker on the two top screws and install the bottom screw. It took about two hours for the new Ice Maker to start it's cycle but after it did, it worked GREAT. Part Select service was OUTSTANDING, ordered part one day and received it in two days and I live in a very remote location. Recommend PartSelect to everyone.

I unplugged the refrigerator(for safety). Using a 1/4" nut driver I removed 1 screw holding ice tray rack. I then removed the 2 screws holding the lower shroud inside the freezer section. I then removed 1 screw holding cover plate where ice maker would be and disconnected the ground wire from the back panel. I then removed the 2 screws holding the back panel in place. This allowed me to removed back panel from from inside the freezer. I removed the fan blades from evaporator motor by pulling straight away from motor. I was then able to disconnect the power wires and the ground wire from evaporator motor. Using the 1/4" nut driver I removed the 2 screws holding the front motor bracket and removed the evaporator motor from its bracket housing. Using the an electrical cord that i had fashioned with two female spade connectors on each lead of the wire, i connected these to the motor and plugged the male end of the electrical cord into a standard 110v outlet to verify that the motor was in fact the defective component. The motor did not operate so I replaced the evaporator motor with a new motor and put everything back in reverse order. The refrigerator is running like a champ and keeping the refrigerator contents a cool 42 degrees. Thanks PartSelect.com

the repair it good and easy ,vo helper to do it.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

I followed the video on the web site. Easy squeezy.

Should have. . . . Just taken the ice maker out in the first place . . . . When I saw no ice I assumed the timer was bad. . . Replaced it. . Then when that didn't fix it again assumed that water valve was bad. . . . Replace that also to no avail. . . . Finally took out the ice maker and saw that the heater had stopped working cuz there was still ice stuck in it. . Replaced ice maker. . . All good. . . The water valve I replaced was a good thing cuz you can definatley tell the difference. . . . Anyway. . . Fixed!

Online I learned how to diagnose the problem and order the part I needed. Replacement was simple and now we have ice. It works perfect, no adjustments needed.