RT21LMXKQ09 Roper Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
ice maker did not function
watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.
Parts Used:
-
Gary from Garfield, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
ice maker was leaking and not making correctly making ice cubes
ice cubes are now being made properly and there is no more leaking.
Parts Used:
-
Melba from Aberdeen, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
No ice
I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.
Parts Used:
-
Janis from Virginia Beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No Light
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Parts Used:
-
Mary from Jefferson Township, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Iscles Hanging From Underside Of Icemaker & Frozen "Pudles" In The Ice Bin.
Previous to installing the new ice maker - I replaced the dual inlet water valve per the instruction video I found @ partselect website. That did not solve the problem <> I also adjusted the timer on the old ice maker down - per another video / which also did not solve the problem. Then I viewed the video on icemaker replacement - ordered the ice maker & 3 days and 15 minutes later <> the problem was fixed ! This web site is "fantastic" ! Thankyou partselect for your assistance ! ! !
Parts Used:
-
NEAL from boyton beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Part Where Ice Maker Arm Fit In Broke Off
Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect
Parts Used:
-
Yvonne from Worthington, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lower part of refrigerator was not cooling
About 7 screws total. ! screw holding side shelf removed. 2 screws holding bottom rear panel removed. 2 screws holding rear panel top removed. 2 small screws holding the fan motor bracket. Remove 3 wire connectors from fan motor and then remove plastic fan(pull off) Then just reverse the procedure. As always please make sure unit is unplugged. If there is ice buildup in freezer use a blow dryer to melt and then dry unit. Very easy fix!
Parts Used:
-
Peter from Oswego, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker would not eject ice from the ice tray.
Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!
Parts Used:
-
Todd from Meridian, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker failed tp produce ice
Removed three screws. Discount wire harness. Reverse proceedure for installation.
Parts Used:
-
Peter from Punta Gorda, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
old icemaker went bad the form tray bubbled up and held cubes in place that stripped the drive gears at the motor end
Watch the u-tube video first ,Then read instructions that came with new unit ! so darn easy. unplug fridge, remove ice bin, clean and dry bin before putting back in service! stick flashlight in freezer loosen 2 top screws remove 1 bottom screw, unmount unit, unplug wire harness, remove icemaker and put on table, close freezer door !! , Remove sensor arm from old unit in down position and install in new unit. plug in new unit and reattach in freezer. replace ice bin and plug in fridge, that's it!, It took about 2 hours for the icemaker thermostat to say OK lets go had a load of ice in aprox 3 hours from finish. piece of cake. Jon
Parts Used:
-
Jon from Barnegat, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Parts Used:
-
Albert from Dunmore, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped making ice
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.
Parts Used:
-
Richard from Stephens City, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No cold air reaching refridgerator
I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.
Parts Used:
-
David from Gastonia, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced Ice Maker
The replacement ice maker came with a few different wiring harnesses which I assumed one of them would fit. well none of them did. I took the wiring off of the old one and matched up all of the receptacles and hoped for the best. It worked. The hardest part of the repair was dislodging the ice machine from the massive chunk of ice that had developed due to the leak in the old one. after that it was pretty easy. I hemmed and hawed about the wiring harness for a few minutes but felt confident it was going to be okay. I took the heat shield off of the old one and put it on the new one and used the control cover and the control arm from the old one too. I checked that all the holes and mounting assemblies matched up. I plugged in the wiring harness to the ice maker and than to the refridgerator, used a nut driver to secure it to the inside wall of the freezer with 3 screws, replaced the ice bucket and the cold air diverter and closed the door. Within an hour I heard the first ice hit the bottom of the bucket.
Parts Used:
-
Patrick J from MORRISTOWN, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Parts Used:
-
Don from Laramie, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!