Models > RST399UW (P1132622N W) > Instructions

RST399UW (P1132622N W) Caloric Range - Instructions

All installation instructions for RST399UW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RST399UW
76-90 of 95
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

three of four burners would not ignite

  • Customer: Stephen from Cambria CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am writing this post to hopefully save someone else the frustration and confusion I experienced when I ordered a replacement ignition module for an Amana gas cooktop AKGD3060WW. Over time, three of the four burner would not light. I ordered a replacement spark module from PartSelect and to my surprise it arrived the next day.

The installation instructions were very confusing. I read the instructions posted by prior customers about this part and none of them helped or seemed to apply to the same cooktop. With the use of the exploded view on PartSelect website I was able to figure out where the module was located.

I turned off the gas and unplugged the unit.

I had to go under the cabinet and securely prop up the cooktop cavity box from below as I had to take off the whole cover, which was actually holding, or mounting, the unit to the counter top.

I removed the cooking units then, the control knobs and the glass control plate, and the vent filter and vent cover. After removing about 20 screws from the main frame/cover I located the spark module at the rear of the unit, sandwiched between two pieces of sheet metal and obstructed by numerous wires. I recorded the wire connections then unplugged the module. It was difficult to remove module due to the numerous unrelated wires that were routed through that area.

I connected the wires to the new module (NOTE: The replacement module has no terminal identification.), plugged the cooktop into the power and tested it and noted that all four burners now received a strong spark.

The original unit is smaller than the replacement unit and the supplied bracket does not fit this cooktop. I had to force the module into position. I removed the two small tabs and applied double sided tape applied to the bottom then secured it against the original mounting bracket. I then adjusted the wires back into the recess with the module and reassembled the cooktop.

The cooktop now lights all four burners instantly, for the first time in several years.

This Amana gas stove is believed to have been manufactured in 1996 or thereabouts. The burners stopped self-igniting one at a time about 1.5 years ago. Since then we have lit the burners with a gas grill lighter.

  • Customer: Chris from Piedmont SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Using a meter, we determined each of the four igniters had continuity from end to end and also had continuity from the end of each igniter back to the spark module. At that point we decided the module was probably bad and, after reviewing some similar-sounding problems on this website, I ordered the module. Installation was simple and solved the problem. All four burners now ignite as they should. One caution - the installation instructions that came with the new module did not describe anything like my stove.

Old igniter lost power to ignite gas..

  • Customer: Blair from Florence NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

Oven stopped working with functioning ignitor

  • Customer: Angela from Brewster MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Turned off gas supply and power. Removed four wires by hand and with a needle-nose pliers after making simple schematic. Disconnected gas supply to valve and valve outlets to broiler and oven. Also loosened other end of gas supply (on regulator) to swing it out of the way. Tools used....open end wrenches. Removed two nuts on left side of valve holding valve to bracket. Tools used...1/4" socket set. Since the nuts holding the right hand bracket were difficuly to reach, I removed the bracket, allowing the valve to be removed. Tools used....1/4" socket set. I then removed the right hand bracked and mounted it on the new valve. I then installed the new valve in the reverse order. I then opened the gas supply and tested the inlet connection(s) for leakage with soapy water. Perfect seal. I turned on the power, set the clock, and tested the oven and broiler. Worked perfectly. The only thing that prevented this from being a really easy job was the location of the valve....in cramped location.

Oven door hinge broken

  • Customer: Sherry from Mountain Ranch CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Oven no longer came on

  • Customer: jeffry from Sussex NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Ignitor would not ignite the oven

  • Customer: Fletcher from Greenville SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher

oven light replacement

  • Customer: martin from portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

broken hinges on oven door.

  • Customer: DAVID from FRANCISCO IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I HAD ALREADY REMOVED THE OLD HINGES BY REMOVING THE SCREWS/BOLTS AND REMOVING THE BROKEN HINGES FROM THE BACK SIDE THROUGH THE DRAWER BELOW THE OVEN THAT I HAD ALREADY REMOVED. TOOK THE NEW HINGES AND SCREWED THE TWO METAL SCREWS INTO THE TOP HOLE ON THE NEW HINGES AFTER PLACING HINGE IN VISE, ONE SCREW ON EACH THEN REMOVED THEM AND PLACED THEM TO THE SIDE. DETERMINED THE RIGHT TAP FROM MY TAP SET, AND THEN TAPPED THE BOTTOM TWO HOLES ON THE NEW HINGES, ONE ON EACH. PLACED THE BOLTS THAT CAME WITH THE NEW HINGES INTO THE HOLES I HAD JUST TAPPED, SCREW THEM IN, THEN I REMOVED THEM AND PLACED TO THE SIDE. TOOK HINGES AND BOLTS / SCREWS TO THE OVEN, INSERTED HINGES IN THROUGH THE DRAWER THAT I HAD REMOVED UP TO EACH SIDE WHERE HINGES WOULD COME BACK OUT TO THE FRONT OF THE OVEN. PLACED SCREWS / BOLTS ONE AT A TIME THROUGH OVEN DOOR FRAME INTO THE HINGE ON THE BACK SIDE, AND THEN THREADED THEM INTO THE HINGES AND TIGHTENED. REPLACED OVEN DOOR ONTO NEW HINGES AND CHECKED FOR CORRECT OPERATION. DOOR WORKS LIKE NEW.

OVEN DOOR HINGE WORE OUT

  • Customer: Richard from La Crosse WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I keep my several rentals in better shape than most people keep their own homes. When an oven door hinge wore out on a home that I rent, I replaced it with one ordered from Parts select. It arrived shortly thereafter! Wow. The woman on the phone solved the biggest problem: finding the cross-over number. I had been quoted US/$80 for the hinge until she found the replacement number and sent it for a total of less than one-half. I can't imagine checking anywhere else for appliance parts in the future! Thanks. -- R. Goodhart -- La Crosse, WI

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Door wouldnt shut evenly.

  • Customer: David from Westlake OH
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

Burners would not light everytime they were used.

  • Customer: Blaise from Deer Park TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.

SCREWS WERE RUST6ED, MELTED

  • Customer: VICTOR from MOUNT PROSPECT IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
USED GRINDER TO CUT THE SCREWS. ALL 4 SCREWS HAD TO BE CUT TO REMOVE FROM BURNER ASSEMBLY. ONCE THIS WAS ACOMPLISED IT WENT FAST WITH NO PROBLEMS
All Instructions for the RST399UW
76-90 of 95