Models > RST399UL (P1132642N L) > Instructions

RST399UL (P1132642N L) Caloric Range - Instructions

All installation instructions for RST399UL parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RST399UL
61-75 of 95
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken hinge on oven door

  • Customer: Robert from Morgan Hill CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 7 people found this instruction helpful
I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

The burner would not light but the ignitor lite up fine.

  • Customer: Tom from West Allis WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

The oven was not heating properly

  • Customer: Douglas from Aurora IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.

to[p light burned out

  • Customer: Christopher from Tyler TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
repair wasn't the issue, finding the part was. I went to home depot - no matching bulb and for some reason I never found out, weren't able to order one, same thing at lowe's - then I went to a electric supply house - and they ordered one but it wasn't the right part. Found your web site and easliy found the bulb and ordered it, GREAT! took the standard 3 - 5 day thinking that it had been 2 months waiting on finding the bulb, surley I can wait 3 - 5 days... this was on a thursday afternoon - Fed Ex delivered the bulb the early on saturday morning! the charge had barley showed up on my card and the part was here! and was less expensive than the price at the electric supply house! Count on my business again, I saved you site in my favorites

hinge on oven door broke off

  • Customer: Janine from Wilkes Barre PA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 5 people found this instruction helpful
After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Wall Oven - Igniter burning out.

  • Customer: Rianna from West New York NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
I researched the needed part (igniter)and purchased it on line. It arrived promoptly. I called a repair person who arrived and installed the new part. All is well.

Oven gas flash, igniter not heating up enough

  • Customer: Nelson from Selden NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Removed old igniter held by one bolt & nut, diconected two leads to igniter. Gas mainifold remained in place during repair. Replaced with new igniter, using old mounting bracket and wire ties. Total repair time 30min, oven repair service wanted to charge $80 just for diagnosis. Total cost of repair doing it myself was $50.

the iron gets red hot but not enough to open the gas valve.

  • Customer: Paul from SEWAREN NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

broken hinge

  • Customer: Jed from Spanish Fork UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Oven ignitor stopped working

  • Customer: john from lancaster CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Took off oven door, took out racks and bottom plate, removed burner assembly disconnected wires, removed old ignitor put new one in holder, connected wires, put burner assembly back, checked if it worked and replaced racks ect..No tools needed.

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

the oven would not light

  • Customer: Kathy from Arlington WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ago.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.

Oven would not ignite

  • Customer: Ronald from Dedham MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the ignitor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.

old tube burned out

  • Customer: JERRY from SPANISH FORK UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Door gasket gotten hard

  • Customer: Richard from Pocomoke City MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
I took oven door apart and replaced old gasket with new one.
All Instructions for the RST399UL
61-75 of 95