RST310UW (P1130738N W) Amana Range - Instructions

remove knobs and 2 screws from front panel, remove front panel. remove burner grates and caps. remove 8 screws (2 per burner base). remove each base and unplug wire. remove the top of the range. locate an remove old ingition module with bracket. on my model i did not need the new bracket. the new module fit right in the old one. unplug wires from old module and plug them into the new one in the same place they were in the old one. reverse the order to reassemble. new module does not make the same clikcing noise (not as fast as old one), but it lights on the first click. GRERT JOB PARTSELECT.!!! parts go to my house within 2 days...saved about $40-$50.

Bought a new one. . Three years later =)

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Removed the screws from the range top burners in order to remove the range top. This allowed me access to the control panel. Removed the screws and wires from the old control and replaced with the new control. Put things back together.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.