Models > RSD369 > Instructions

RSD369 Caloric Range - Instructions

All installation instructions for RSD369 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RSD369
46-58 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

old tube burned out

  • Customer: JERRY from SPANISH FORK UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Oven door hinge broken

  • Customer: Sherry from Mountain Ranch CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Oven no longer came on

  • Customer: jeffry from Sussex NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

Ignitor would not ignite the oven

  • Customer: Fletcher from Greenville SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher

broken hinges on oven door.

  • Customer: DAVID from FRANCISCO IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I HAD ALREADY REMOVED THE OLD HINGES BY REMOVING THE SCREWS/BOLTS AND REMOVING THE BROKEN HINGES FROM THE BACK SIDE THROUGH THE DRAWER BELOW THE OVEN THAT I HAD ALREADY REMOVED. TOOK THE NEW HINGES AND SCREWED THE TWO METAL SCREWS INTO THE TOP HOLE ON THE NEW HINGES AFTER PLACING HINGE IN VISE, ONE SCREW ON EACH THEN REMOVED THEM AND PLACED THEM TO THE SIDE. DETERMINED THE RIGHT TAP FROM MY TAP SET, AND THEN TAPPED THE BOTTOM TWO HOLES ON THE NEW HINGES, ONE ON EACH. PLACED THE BOLTS THAT CAME WITH THE NEW HINGES INTO THE HOLES I HAD JUST TAPPED, SCREW THEM IN, THEN I REMOVED THEM AND PLACED TO THE SIDE. TOOK HINGES AND BOLTS / SCREWS TO THE OVEN, INSERTED HINGES IN THROUGH THE DRAWER THAT I HAD REMOVED UP TO EACH SIDE WHERE HINGES WOULD COME BACK OUT TO THE FRONT OF THE OVEN. PLACED SCREWS / BOLTS ONE AT A TIME THROUGH OVEN DOOR FRAME INTO THE HINGE ON THE BACK SIDE, AND THEN THREADED THEM INTO THE HINGES AND TIGHTENED. REPLACED OVEN DOOR ONTO NEW HINGES AND CHECKED FOR CORRECT OPERATION. DOOR WORKS LIKE NEW.

OVEN DOOR HINGE WORE OUT

  • Customer: Richard from La Crosse WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I keep my several rentals in better shape than most people keep their own homes. When an oven door hinge wore out on a home that I rent, I replaced it with one ordered from Parts select. It arrived shortly thereafter! Wow. The woman on the phone solved the biggest problem: finding the cross-over number. I had been quoted US/$80 for the hinge until she found the replacement number and sent it for a total of less than one-half. I can't imagine checking anywhere else for appliance parts in the future! Thanks. -- R. Goodhart -- La Crosse, WI

Door wouldnt shut evenly.

  • Customer: David from Westlake OH
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

SCREWS WERE RUST6ED, MELTED

  • Customer: VICTOR from MOUNT PROSPECT IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
USED GRINDER TO CUT THE SCREWS. ALL 4 SCREWS HAD TO BE CUT TO REMOVE FROM BURNER ASSEMBLY. ONCE THIS WAS ACOMPLISED IT WENT FAST WITH NO PROBLEMS

Lower Bake Ignitor would glow, but would not ignite flame.

  • Customer: Robert from Sapulpa OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

Broiler & burners worked, oven would not ignite or heat up.

  • Customer: Mary from Weston CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

stove sometimes would not light or took really long and did not maintain heat

  • Customer: Patricia from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Oven would not light.

  • Customer: George from UKIAH CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.

Old igniter lost power to ignite gas..

  • Customer: Blair from Florence NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.
All Instructions for the RSD369
46-58 of 58