RS22AQXMQ01 Roper Refrigerator - Instructions

I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

Easy repair, just snapped the old bins out and put the new ones in. It took longer to empty the old bins and fill the new ones. Customer service was excellent, also my order was to me in 2 days. Great service. Thanks PartSelect

I looked at the video that part select send. I did exactly what it said to do,and now my refrigerator is working just great. And the noise is gone. I thank you so much for your help. And I'm a 64 year old women thats how easy it was.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

It was wonderful. I struggled with the old ones taping them and repairing them until it just didn't work anymore. Within two days they were here and problem solved. What a relief.

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

I can tell you they had the tray to my house within 3 days!! AM I IMPRESSED! Also they were a lot cheaper than ordering the same part from the major store where I bought the fridge. Thanks!

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.

ice cubes are now being made properly and there is no more leaking.

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Thermostat replacement

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.