Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
1,306-1,320 of 1,407
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Compressor fan and motor was load,barring was wobbling .

  • Customer: William from Fox lake, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Fast after a little help from a friend

Ice maker stopped making ice

  • Customer: Richard from Stephens City, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

The drum just started breaking apart one day. i thought i'd have to buy the entire auger. But as a result of Parts Select, Irealized i only needed to buy the drum.

  • Customer: Li from Long Beach, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Before I ordered, I followed the great video to disassemble the unit. That's when I realized I only needed to buy the drum. Five days later, I had the part. I thought I remembered how to reassemble it, but I ended up needing to watch the video again. It wasn't difficult, but you must get all the bits back in the same order!! Once that was dine, it all went together easily. Thank you! I'm so impressed with this site that I posted on Facebook about it so my friends can also save big bucks doing simple repairs themselves.

Water dispenser did not work. Ice dispenser did work.

  • Customer: Thomas from Egg Harbor, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I first viewed the instructional video provided by Partselect to pin point the faulty part. It was the control bracket. I would not have known how to expose the control bracket if it weren't for the video. Also Partselect said 48% of past water dispenser problems were the control bracket; this also helped me pinpoint the faulty part. I ordered the part; it arrived in 3 days. Using the video as a guide I repaired the dispenser in about 20 minutes start to finish. I will always go to Partselect for all appliance problems.

broken bins

  • Customer: jeannie from roanoke, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was very simply and easy My kids tend to use the door bin to shut the fridge I Was able to buy 4 new 1s for a great price and fast delivery .Thanks Parts Select :)

Replaced Ice Maker

  • Customer: Patrick J from MORRISTOWN, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The replacement ice maker came with a few different wiring harnesses which I assumed one of them would fit. well none of them did. I took the wiring off of the old one and matched up all of the receptacles and hoped for the best. It worked. The hardest part of the repair was dislodging the ice machine from the massive chunk of ice that had developed due to the leak in the old one. after that it was pretty easy. I hemmed and hawed about the wiring harness for a few minutes but felt confident it was going to be okay. I took the heat shield off of the old one and put it on the new one and used the control cover and the control arm from the old one too. I checked that all the holes and mounting assemblies matched up. I plugged in the wiring harness to the ice maker and than to the refridgerator, used a nut driver to secure it to the inside wall of the freezer with 3 screws, replaced the ice bucket and the cold air diverter and closed the door. Within an hour I heard the first ice hit the bottom of the bucket.

Ice maker stopped working altogether, dead.

  • Customer: Glen from Gilbert, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The unit was old so I opted to buy a new one even though it was just the motor. It took about 10 minutes to remove it after locating the fasteners, possibly less and about the same to install the new one. When the unit is turned on for the first time it does not start up right away. It will not start until it senses that it is cold enough in the freezer. For me that was about an hour to an hour and a half. There was a note on the cover that this could be as long as thirty six (36) hours. So don't be alarmed when it does not start running right away. The instructions were accurate.

The refridgerator door would not shut on its own. It had to be pushed completely shut every time it was opened.

  • Customer: Fred from Dacula, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.

small plastic part in the icemaker control assembly broke, disabling entire system

  • Customer: Linda from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Ice would not dispense through front of door. There was no sound when the lever was pushed either, however, the water dispenser next to it worked fine.

  • Customer: John from Cresskill, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

refer not getting cold

  • Customer: richard from WYANDOTTE, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed cover unbolted thermo an replaced no big deal

The Refrigerator Was Running But Blowing Hot Air, Everything In Freezer Had Defrosted.

  • Customer: Jeanne from Fairview Heights, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

Ice maker would not make ice

  • Customer: Daniel from Central, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

icemaker stopped working

  • Customer: Patricia from Urbandale, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

The Ice Bin Auger Drum shatered away from the shaft.

  • Customer: Robert from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.
All Instructions for the RS22AQXMQ01
1,306-1,320 of 1,407