RS22AQXMQ00 Roper Refrigerator - Instructions

Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

We moved into a house that we are renting. The whirlpool refrigerator was missing the the ice shoot. The landlord wouldn't hire someone to install one. I am %95 blind. I went on PartSelect , entered the refrigerator and they had an easy blow up diagram. I ordered the part and watched a video on how to install it. When the part came in my son watched the video and had it installed. Hats off to PartSelect for their great web site .

I followed the video on the web site. Easy squeezy.

remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

Should have. . . . Just taken the ice maker out in the first place . . . . When I saw no ice I assumed the timer was bad. . . Replaced it. . Then when that didn't fix it again assumed that water valve was bad. . . . Replace that also to no avail. . . . Finally took out the ice maker and saw that the heater had stopped working cuz there was still ice stuck in it. . Replaced ice maker. . . All good. . . The water valve I replaced was a good thing cuz you can definatley tell the difference. . . . Anyway. . . Fixed!

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Just lifted out one out and sit new one in place

Looked on YouTube and found the PartSelect video. Viewed the video and replaced the part.

Online I learned how to diagnose the problem and order the part I needed. Replacement was simple and now we have ice. It works perfect, no adjustments needed.

We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH

When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

I followed the UTube video step by step, pausing at each section made repair very easy. Watching the video is a definite must!

Simply done !

snapped in new bins.