Models > RS22AQXMQ00 > Instructions

RS22AQXMQ00 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ00
1,321-1,335 of 1,470
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My ice maker quit working

  • Customer: pauline from somerville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have some electronics background but your listed problems helped me narrow down the problem. I ordered the part, removed old part, installed new part (maybe 15 minutes total) and my icemaker started dumping the ice that was in the tray within 20 minutes and making more. That clunking sound of ice was music to me ears and wallet!! Thanks!!

Ice maker wasn't getting water

  • Customer: Anna from Morgan Hill CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called a repair man out to see what the problem was because my husband just died and I didn't want to pay such high prices for a repair. He told me I needed a new motor for the ice maker and it would be a total of about 305.00. I couldn't believe the price. It cost me 59.99 for his diagnosis. I went to your web site and found the part and watched you installation video. I am 65 years old and I was able to install the new part in less than 15 min. The part was about 95.00. I saved 150.00 by doing it myself. I will always look on line before I have a repair man do a job. I may need them to diagnose the problem, but I will try myself before paying such outrageous fees.

Ice Maker stopped working. Already replaced Photo Eye

  • Customer: Alfred Van from Lutz FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

Ice maker quit working

  • Customer: Donald from Banning CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

couldnt use ice maker dispencer. ice melting and leaking

  • Customer: Kevin from Wyandotte MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

ice door would not seal warm air out & ice maker would freeze up.

  • Customer: Earl S. from Denison TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

Refrigerator and freezer was not cooling. Lights inside refriogerator working . Compressor and fan was not on.

  • Customer: Cary from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug the refrigerator. With nut-driver and/or screw driver remove the lower back cardboard panel to access Start device. Use needle nose pliers to remove bracket holding Start Device along with capacitor. Disconnect the wiring connector from Start Device. Carefully, pry Start Device from compressor. Remove capacitor from Start Device. Replace the capacitor to the Start Device. Connect the Start Device with the capacitor to the compressor being mindful of the three male pins. Plug the electrical connector back into the Start Device. Finally, reconnect the bracket. . Reinstall the lower back cardboard panel. Plug in the appliance. Very simple and easy to install. Note: If the compressor and fan do not come on, reset the defrost switch which is located inside the refrigerator side underneath the right side of the refrigerator temperature selector with the flat head screw driver.

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Ice dispenser was broken

  • Customer: Helen from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!

Refrigerator Freezer Ice Door Broken

  • Customer: Peter from Wildomar CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Job went as per your terrific video. Except that when attempting to retrieve the old heater element the glue on the old door was no long pliable. I had to literally tear the old foam apart to get at the heater element and almost damaged it. Not to worry. It worked out well and all is great. Thanks for the very instructive video.

Door was stuck open

  • Customer: Stewart from Crosby TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
If you follow the video to the letter it's a piece of cake

Ice dispenser on door was disfunctional

  • Customer: Wayne C. from Metairie LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

ice chute door was warped allowing warm air into chute causing freeze up of chute. Would my dispense ice.

  • Customer: Peter from Westminster SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.
All Instructions for the RS22AQXMQ00
1,321-1,335 of 1,470