REL4634BW2 Roper Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer not getting hot enough, taking to long to dry
Pulled dryer from wall, disconnected electrical plug, disconnected dryer vent, check vent flapper for proper operation, took back from dryer, replaced upper limit and heater limit, reinstalled all, checked dryer vent for obstructions, works fine now...
Parts Used:
-
James from Arapahoe, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
belt broke
-
Virgil from Angleton, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drum was not turning
I watched your video and did the job,really no problem. I also cleaned out all the lint and dust will the drum and front were out.
Parts Used:
-
John from West Islip, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer belt broke
Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video
Parts Used:
-
mark from montrose, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer Belt Broke
Fortunately this is an easy diagnosis and easy repair. The great PartSelect instructional videos are a HUGE HELP!!
Parts Used:
-
Reid from Cumming, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
loss of heat
-
Timothy from Southamton, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not run or start at all. Seemed like it had no power but the light still worked and it wasn't the breaker.
Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!
Parts Used:
-
Joshua from Sturgeon Bay, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Followed the instructions that came with belt everthing went just fine.
Parts Used:
-
Rick from Emporium, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door switch broke
I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.
Parts Used:
-
Jeff from Mamaroneck, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would only run for a few mins and then not restart. Also there was a grinding noise.
I replaced the entire motor in the dryer and the belt while I had it open and it is working great! I just watched the short video on the site to learn the tricks and did it myself.
Parts Used:
-
Andrew from Lawrenceville, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gas burner would not fire.
First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys
Parts Used:
-
Leif from Plainfield, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
no heat
remove 4 screws,unplug old part, put in new one put back of dryer on the hardest thing to do was moving the dryer to get to the back
Parts Used:
-
Norma from Union Gap, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The control panel won't leave Casual load.
Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.
Parts Used:
-
Ann from Cincinnati, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The dryer belt broke.
I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.
Parts Used:
-
Bill from Cooper City, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor hum on start-up
Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.
Parts Used:
-
GREG from BLAIRSTOWN, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!