REL4634BW2 Roper Dryer - Instructions

In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

The repair was easy--thanks to your excellent videos--also, delivery was prompt and correct--your service is excellent--but, looks like I'll need another part--maybe door latch??? I'll troubleshoot and definitely contact PartSelect--Thank you--will recommend you!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

The repair took approxamitly 10 minutes from the time I unplugged the dryer from the wall to the time I had the parts switched out. Very easy anyone could do it.

Based on the PartSelect analysis my heating element was mostly likely the problem. I ordered the part and watched the how to video before it came. The repair was very simple and straight forward. So simple, that I did not need to review the instructions or rewatch the video. Took me about 30 minutes, and the analysis was correct. I also took time to vacuum out all the dryer lint that had accumulated inside on the back of the dryer. Put everything back together, plugged it up, and it was instantly heating up and drying as it should. I am very pleased with my PartSelect experience.

Replace the heating element and themostats. Saved me $$$ from me buying a new dryer. Thank U for the videos also. Great help.

disconnect power - remove back panel - test continuity of thermo control switches - one is open (infinite resistance). Replacement kit consists of two switches - just replace the one that is open. turn on power - dryer now heats.

I removed the back panel of the dryer and the thermal fuse was about three quarters down the dryer. The exploded parts schematic was very helpful. I simply removed two screws to replace the thermal fuse and reinstalled the back panel. The dryer works great now.

I ordered a cycling thermostat and a thermal fuse to start with and put in the dryer. This didnt fix it so I then ordered a heating element. I took out the old one from the dryer and put in the new one that I ordered and received in a couple of days. It heats and runs like a new one now.Thanks for the quick service!

Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

Using the video on the site I was able to open the back on the dryer, replaced the thermal fuse and close it up in less than 15 minutes. Works great and saved me a ton of money.

I simply unplugged the dryer and removed the backing. Once off I located the part which was in plain sight, unhooked the wires and attached them to the new part. Put backing back on plugged it in and turned it on and it worked.

Followed the directions for a element repair on Youtube. Found one that looked like our dryer. You took the back off and then the element had 3 wires and another electronic thingy (thermocouple?). Old element slips out and confirmed it was dead with a multimeter. Ordered new one through this site (they had a great schematic too). Came really quick and we reinstalled it. Dryer maker was a genius and all three heater wires had different size heads so we couldn't even screw it up. Put everything back together and we have a fixed dryer!

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing back together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.