REL4622BW2 Roper Dryer - Instructions

Watch the video you sent me, and every thing fell into place

My husband followed your video

I reviewed the on-line video (which was very good by the way) and read the instructions that came with the thermal cut-off kit. Replacement of the upper thermostat was a piece of cake, very straight-forward; just remove the old & replace with the new. The instructions for replacing the lower thermostat were a little confusing because my dryer did not have the orange wire coming from the wiring harness, but after looking carefully at the old thermostat and how it was connected, I finally figured out how the jumper wire was to be connected and successfully installed the lower unit. Bottom line...the dryer works like new. Much cheaper than calling the repairman! Thanks PartSelect!

Unplug the dryer, take off the rear panel with a nut driver, remove the old heating element (3 screws). remove the thermostat attached to the element, put the thermostat on the new element and install the new element with old screws. re install the back panel with old screws and you are done. Plug it in and it's ready to go!

removed back cover 9 screws , 2 screws on heating element and it pulled out ,3wiers and the new one went in. thermal fuse, was one screw and two wiers and I was done.

Removed top and front of dryer. Removed drum. Removed old rollers from spindles. Installed new rollers and new retainer triangles. Replaced drum. Re-installed front and top.

I made it very difficult. I didn't research the repair. My back is old. It's easier if you just You Tube a video. The top roller you have to take drum completely out. The bottom one, The one that failed for me, you can actually do it without taking anything apart. Access it at bottom back, two holes. I do not have small hands, it would have been easier. Channel Locks inside, 9/16th socket outside. That will loosen main axle. Then use short screwdriver or socket driver on small bracket connected to bottom of unit. Mine had one screw holding it in. Easy bottom fix. I don't really recommend replacing top till it needs it. You can only buy them by the pair too. You will be ready when time comes. I found top roller didn't actually need replacing, did it cause I had it all apart. Don't fix if not broke, right? Trust, BUT, Verify. Smaller hands, would have helped me. All I got.

In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

The repair was easy--thanks to your excellent videos--also, delivery was prompt and correct--your service is excellent--but, looks like I'll need another part--maybe door latch??? I'll troubleshoot and definitely contact PartSelect--Thank you--will recommend you!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

The repair took approxamitly 10 minutes from the time I unplugged the dryer from the wall to the time I had the parts switched out. Very easy anyone could do it.

Based on the PartSelect analysis my heating element was mostly likely the problem. I ordered the part and watched the how to video before it came. The repair was very simple and straight forward. So simple, that I did not need to review the instructions or rewatch the video. Took me about 30 minutes, and the analysis was correct. I also took time to vacuum out all the dryer lint that had accumulated inside on the back of the dryer. Put everything back together, plugged it up, and it was instantly heating up and drying as it should. I am very pleased with my PartSelect experience.

Replace the heating element and themostats. Saved me $$$ from me buying a new dryer. Thank U for the videos also. Great help.

disconnect power - remove back panel - test continuity of thermo control switches - one is open (infinite resistance). Replacement kit consists of two switches - just replace the one that is open. turn on power - dryer now heats.

I removed the back panel of the dryer and the thermal fuse was about three quarters down the dryer. The exploded parts schematic was very helpful. I simply removed two screws to replace the thermal fuse and reinstalled the back panel. The dryer works great now.